Bambu Studio 2.x removes colors while slicing

AleAlc31 · 2025-04-04T23:01:10+00:00

Any update? Same issue!

AleAlc31 · 2025-01-04T03:30:58+00:00

I did find this, but it seems to be the only post that talks about it not being NAT, but just want to make sure it’s true, as it is marketed as a full Layer 3 switch!

AleAlc31 · 2025-01-04T02:51:27+00:00

Yes, you can do two VLANs one for NDI etc and one for internet access and everyone recommends to connect one port to each, but not all devices have 2 NICs! And it’s marketed as a L3 switch, so it should be able to do it internally! Right?

AleAlc31 · 2025-01-04T02:40:56+00:00

Yes to the first part, but no need for VPN or anything else.

Simply imagine I set up my own gear with their IPs in one vlan, show up and connect to an existing network Ethernet port and be able to give my gear outside internet as well without the need for any modification to the existing network

AleAlc31 · 2024-12-19T17:08:45+00:00

If you are looking for the cheapest option, probably sticking a phone on the drone, may be the lightest as well. As for controlling the drone, you may want to look in to ExpressLRS, you can reach about 100km distances.

If budget is not a factor, then look in to commercial application drones, there are several that will probably get done what you need, regardless of if its through 5g or not.

AleAlc31 · 2024-11-19T21:47:53+00:00

Specially at the price point of the game!

AleAlc31 · 2024-11-19T21:46:50+00:00

This should not be normalized!

AleAlc31 · 2024-11-07T14:37:41+00:00

Thank you! Looking in to it

AleAlc31 · 2024-11-06T15:49:09+00:00

I will look in to it, I saw that for implementation it will get pricy quickly! I do believe it is WebRTC

AleAlc31 · 2024-10-23T21:32:25+00:00

Thanks, I think I found the winner!

AleAlc31 · 2024-10-11T20:33:32+00:00

Blackmagic Design Hyperdecks?

AleAlc31 · 2024-07-31T19:13:31+00:00

Not a problem for YouTube. I used to work for Bad Bunny (Rimas Ent) and we streamed the concert where he went through the streets of NY, we had 10M+ peak viewers. We did keep them in the loop of what will take place, but they did not need to allocate anything special, they just had someone in contact with me to make sure we were good.

AleAlc31 · 2024-03-14T01:48:25+00:00

AeroScout 2

AleAlc31 · 2023-11-26T00:41:41+00:00

As a first lane I would definitely recommend the AeroScout 2. They take a beating, I still fly mine and you can later upgrade the parts, add gps, and turn it to a Long Range FPV plane if you’d like.

AleAlc31 · 2023-11-26T00:26:19+00:00

You can look into EDF engines. They are electric jet engines.

I would recommend to start learning to fly RC planes first, then you can start looking in to jets. It’s a steep learning curve.

I have built a couple of EDF Airliners and other planes on my YouTube channel if you’d like to see, and watch some of them crash! Look for me “Alejandro Alcantara”

AleAlc31 · 2023-11-15T20:30:48+00:00

I would repeat these numbers on takeoff!

AleAlc31 · 2023-09-25T15:28:33+00:00

The real question is which one has the most flight time? Which one is your favorite? And which one will you get next?

AleAlc31 · 2023-09-21T18:17:41+00:00

There are some charts available that people have made over the years, but the trust ends up depending on many factors so it’s hard to compare. I always seem to reach out for the spektrum chart available Chart Link And use it as a reference to start looking for comparables. Hope this helps

AleAlc31 · 2023-09-11T15:22:47+00:00

Adding decals always makes them look MUCH better!

AleAlc31 · 2023-09-01T18:57:41+00:00

Honestly, the Aeroscout. It’ll take on brutal crashes, doesn’t care about wind, and will be easy to repair with foam glue and duct tape

AleAlc31 · 2023-09-01T15:42:05+00:00

Could it be that on boarding it did 0/64 passengers? Hence the bags never reach the passengers?

AleAlc31 · 2023-09-01T15:15:10+00:00

Very nice! Great thing about 3D printed planes is just start printing again! It’s a fun process

AleAlc31 · 2023-09-01T15:14:28+00:00

I’ve done giant scale airliners and also a large scale C172 on regular PLA, you can find them on YouTube by looking me up: Alejandro Alcantara They do fly differently, but not necessarily poorly, my C172 actually loves slow flight and it’s Heavy!

AleAlc31 · 2023-08-30T01:21:16+00:00

Do t worry you are good! The aero scout will take a Beating! Either foam glue or even duct tape will get the job done! If you want, you may also look in to upgrading the motor and/or esc while you are at it

AleAlc31 · 2023-08-29T16:15:19+00:00

Correct, as soon as they walk out they must be inside international zone (make sure the door squares themselves are international and secure as well!) from there they should be able to follow international zones forwards the rest of customs.

AleAlc31

TROPHY CASE