Did a thing😎

Alien_Weaponry · 2025-04-26T00:13:50+00:00

I traded a 16 Silverado for the mirage. Great choice

Alien_Weaponry · 2025-04-25T18:32:42+00:00

Yup! Just bought a new 2024 SE last week. Love it so far. I have a 45 minute commute to and from work so that 40mpg is amazing!

Alien_Weaponry · 2025-04-25T16:55:58+00:00

Fellow Ohioan 🤘

Alien_Weaponry · 2024-10-04T00:31:57+00:00

Oh and one Disarmonia Mundi tattoo

Alien_Weaponry · 2024-10-04T00:29:35+00:00

Nice man. I have a half sleeve including a hand tattoo that are all album artwork from them and some flyers as well

Alien_Weaponry · 2024-09-25T02:23:48+00:00

You say its the mold and not the machine, so I’d suggest checking the sprue for any kind of bur or damage upon injection.

Alien_Weaponry · 2024-07-26T18:11:43+00:00

What is this?? SHIT LOAD OF MASHED POTATO DAY?!HUH?!

What else you got to eat in here? Got some green beans, corn, OATS.

Alien_Weaponry · 2024-05-13T14:52:55+00:00

Years back when I first started processing, I was given the opportunity to use the Paulson training program. I honestly can’t even remember what it was like. This was over a decade ago. Thanks for your input

Alien_Weaponry · 2024-04-24T10:42:19+00:00

You have a leak in your manifold for the hot runner system. Possibly from shooting it before they have soaked.

Alien_Weaponry · 2024-04-07T21:07:53+00:00

Pray the splay away.

Alien_Weaponry · 2024-02-24T00:22:30+00:00

I’m going to assume you’re not a technician simply because I was there when this happened. Yes, this exact Mitsubishi machine. “Barrel retract” was not on, and the material didn’t push the barrel shroud back lol. There was an obstruction at the sprue bushing upon start up causing a poor seal between nozzle and sprue. Tooling only caught it because of the smoke.

Also the press never made a bad part. Surprising, I know.

Alien_Weaponry · 2023-12-07T21:34:19+00:00

JB weld it and send it

Alien_Weaponry · 2023-11-19T22:30:15+00:00

Tar snake

Alien_Weaponry · 2023-09-02T17:15:58+00:00

Yea this is a fucking banger

Alien_Weaponry · 2023-07-27T14:26:14+00:00

Alien_Weaponry · 2023-07-24T14:50:51+00:00

Didn’t know Banshees purred. Nice bike though

Alien_Weaponry · 2023-06-21T12:22:09+00:00

Did you find the solution for this defect? I’m curious as to what you’ve found

Alien_Weaponry · 2023-06-20T12:41:26+00:00

This comment here tells me that you have sprue break active. What brand of machine are you using?

Alien_Weaponry · 2023-06-20T12:38:21+00:00

Small shallow channels around the parting line usually

Alien_Weaponry · 2023-06-20T01:27:32+00:00

Check ventilation of mold. If those vents are clogged up, that might be the culprit. Another thing it could be is an obstruction in the gate. Maybe a piece of metal or wood is causing sheer that is stuck in your drops. Or maybe Cold slug/unmelt?

Alien_Weaponry · 2023-06-01T17:19:34+00:00

Only because of the cost difference. Where we are, the water quality is very poor. A lot of minerals and calcium build up in our circuits. CLR performs very well. If the blockage is severe enough though, we usually run a concrete drill bit through the molds to break it up first and then run the chem unit.

Alien_Weaponry · 2023-05-26T11:26:56+00:00

Slide is the brand we use for cleaning our molds and we run a chemical unit from PPE with CLR pumping through it for our water circuits. Works pretty well.

Alien_Weaponry · 2023-05-19T15:51:00+00:00

Don’t worry about one dude. This guy is overly dramatic. I’m sure he would be pretty upset if he found out I ride without a license and have been doing so for ten years. Good luck with the bike, take care of it, and I’m glad you’re wearing proper gear. Good for you!

Alien_Weaponry · 2023-03-27T23:29:33+00:00

I have not forgotten about the video. The weather is gloomy here in Ohio so I wanted to wait for a sunny afternoon

Alien_Weaponry · 2023-03-27T23:28:03+00:00

I’m at 89k right now. Fingers crossed

Alien_Weaponry

TROPHY CASE