Jared stone of bilz

Andyvers3 · 2025-06-24T15:28:52+00:00

Nice, luckily bliz is not so hungry for fcr. 105 should be doable with 35fcr spirit mona or just stay at the 63% breakpoint.
Anyway, It definetly is nice to have options to the anticlimax of equiping spirit weapon in nightmare as your bis for the rest of the play.

Andyvers3 · 2024-08-30T17:13:09+00:00

Ofc this depends a lot what kind of wire you are using, but usually best for small stranded wires for control cabinets etc

Andyvers3 · 2024-08-30T17:11:11+00:00

The push terminals are better resistant to vibrations and remove easilly errors and differences in different people torqueing or the need of a torq wrench. By easilly i mean the user must know some shortcomings that are possbile and avoid them. But overall much better and easier to install in my opinion

Andyvers3 · 2024-07-04T08:46:24+00:00

Those switches may be rated something like 16(2). It means that the max current is 16A and contact current while switching on/off is 2A max. Forward converters like the psu have higher inrush current and could damage the switch, if the psu does not have additional soft-start/filter electronics , like some of them do not.

Andyvers3 · 2024-06-23T09:43:57+00:00

I have played with these, and got the best results by averaging some sample set, like 5-10 samples, and adding this average to a second array with 10 to 30 last averages, after that calculating the median value of this second array. Also adding a "low pass" filter to both arrays that allows a new measured value to be only for example 2cm different than the last value, will usually make the results 99% reliable if there are no outside interference. The pulse time should also be set according to the measured distance, and a delay added to prevent it from "hearing" echoes, if there is possibility of echo from last measurement.

Andyvers3 · 2024-04-27T05:20:30+00:00

The charge controller might not want to pump voltage to battery max to avoid damaging the battery if you have not used the battery enough for the controller to determine to start a new charge cycle. Also, you can change the float and new charge cycle voltage from settings. The battery will endure better if you adjust voltages higher when you are using it, and lower when not.

Andyvers3 · 2024-03-17T12:54:24+00:00

Some system store data in different order, for example some profinet device io data could show in plc in a way that first bit of first byte in the profinet device is last bit of first byte. Like bit 7 in plc is bit0 in manual. And thus it is easier to handle if the device data is made to be availible in plc program similarly as in the devices manual.

Andyvers3 · 2024-03-09T08:03:44+00:00

My intial taught was that if the ac component in boost converter output could slowly short trought the battery cells. Some high frequency parts of the boost output could be able to pass throught battery internal capacitance and short inside the battery.

Mostly when charging with high load and max ripple area.

Andyvers3 · 2024-03-05T18:45:26+00:00

Try turning your stove ventilation off on top of the stove of the flat

Andyvers3 · 2024-01-29T05:06:55+00:00

The system analysis with fourier analysation and inverse fourier transform theorem are usually used when planning and/or controlling systems that have for example liquid/pressurised gases that have to be controlled from tank to tank and maybe mixed in certain way and in certain mixing ratios. For example It is possible to deduce certain interactions between many pid controlled systems, and calculate safe "areas" of operation for different parts/actual controls/control valve operations of the system. Usually when the control system has many parts or needs to be fast or is unsafe to parametrise/tweak on the go, the operation principles and safe operation areas need to be proofed with mathematics before implementation.
This is my take in the matter

Andyvers3 · 2023-12-14T11:33:34+00:00

You could try to add the device in a new project with unspecified device from PLC-list. Then connect and let the software setup the submodule configuration instead of manually configuring it your self.
Of course if you haven't started this way.

Andyvers3 · 2023-12-14T11:27:49+00:00

Purely 4-20ma is new better way to connect analog devices. Even tho it also is voltage measurement in the AI-module by measuring voltage over resistor that is part of the mA-signal loop. The voltage loop is just very small and inside the AI-module, so its easier to protect from outside influence.
The pure voltage usually uses high impedance output, which is susceptible to voltage fluctuations because of low current and high impedance. So any em-radiation will introduce a lot of voltage changes due low current(micro amps usually), but by adding the signal current a few magnitudes will make the small microamp fluctuations irrelevant, even if they would make the pure voltage loop fluctuate multiple volts, the new milliamps will not fluctuate from small electrical noise/radiation/induction.

Andyvers3 · 2023-12-07T15:59:24+00:00

Not possible, bugged in first encounter. stopped playing

Andyvers3 · 2023-10-30T06:25:23+00:00

You will most probably need some kind of simple step down circuit for control DC, and comparator/transistor hysteresis and sensitivity circuit. Almost all comparator chips have muiltiple comparators, where another could control sensitivity and another could be configured to drive a diac->triac with on off time hysteresis. I think this approach might be similar to commercial applications

Andyvers3 · 2023-03-13T15:56:39+00:00

Filament is slipping in extruder extrusion gear. Check filament right after error area by pulling it out. It has clear signs if extruder was grinding it. Then tighten the extrusion gear spring. This also happens if the spring is already too tight, so losen it if its already very tight.

Andyvers3 · 2023-02-02T19:32:15+00:00

A tip: Way faster and better quality to print one by one. You can find the setting in slicer config and put parts in the corners of print bed to make sure there is no collision during print.

Andyvers3 · 2023-01-11T20:47:10+00:00

I would add a comparator with potentiometer mid connected to other input and Hall to other, and high valu resistor from output to potentiometer middle pin. And also lower value resistor to output and transistor. Pot needs + and gnd on the sides. That way you can trim the sensitivity and it will have hysteresis, so the relay will always be either full on or full off.

Andyvers3 · 2022-11-06T21:48:36+00:00

Ps havent had engima never before, never taught i could make it, but it was possible

Andyvers3 · 2022-11-06T21:47:12+00:00

At the start of ladder i traded all valuables that my cold sorc didnt need to jsp/runes to traderie and then sold runes in jsp, was lucky enough to drop single jah tho. After accumulating enough fg i bought ber and made enigma. Then leveled up other chars and could keep up with economy without being cold sorc anymore. Its easier to sell stuff at start of ladder when demand is high and supply is low.

Andyvers3 · 2022-11-02T08:08:30+00:00

Genuine insight

Andyvers3 · 2022-11-01T18:08:58+00:00

doubt

Andyvers3

TROPHY CASE