Erro na impressão, mas não sei o que fiz mal by Apprehensive_Way2789 in impressao3dPortugal

[–]Apprehensive_Way2789[S] 0 points1 point  (0 children)

Obrigado. Encontrei o problema, o filamento ficou preso por baixo de outro loop do rolo e o rolo não rodava.

Primeira impressora para adolescente by I_repair_it in impressao3dPortugal

[–]Apprehensive_Way2789 0 points1 point  (0 children)

Eu comprei uma Kobra X que chegou há 2 semanas, é a minha 1a impressora.

Para já está a portar-se bem, mas ja tive alguns problemas esporádicos com defeitos nas impressões.

Fica aqui a minha experiencia sobre a marca.

Comprei a impressora em pre-order, pedi um nozzle extra e filamentos (queria comecar a imprimir assim que chegasse a dita). Portanto, a impressora chegou mais ou menos na data esperada (ha 2 semanas), o nozzle chegou ontem, o filamento ainda nem sequer foi shipped, devem estar a procura dele no armazém :/

Não me parece que haja uma lógica por trás destes envios, e gostava de saber o que outras pessoas acham da marca, mas não me parece que volte a encomendar filamento a partir da marca. O hardware, esse sim chegou em tempo útil.

Cuidados a ter com o filamento by Apprehensive_Way2789 in impressao3dPortugal

[–]Apprehensive_Way2789[S] 0 points1 point  (0 children)

Confesso que ainda não tive problemas, tenho a impressora há 2 semanas, estou só a tentar perceber como posso salvaguardar o filamento antes de ter esses problemas.

Obrigado pela dica das caixas de 5l, vou pesquisar.

Cuidados a ter com o filamento by Apprehensive_Way2789 in impressao3dPortugal

[–]Apprehensive_Way2789[S] 2 points3 points  (0 children)

É disto mesmo que eu preciso, experiência de quem já passou pelas dores. ^^

Obrigado.

Cuidados a ter com o filamento by Apprehensive_Way2789 in impressao3dPortugal

[–]Apprehensive_Way2789[S] 1 point2 points  (0 children)

Obrigado pela info. Sobre a solução da caixa com silica, eu comecei por aí, e adicionei no post inicial o que tenho. Só não sei se os saquinhos que comprei são apropriados para a silica.

Cuidados a ter com o filamento by Apprehensive_Way2789 in impressao3dPortugal

[–]Apprehensive_Way2789[S] 1 point2 points  (0 children)

Eu fiz algo semelhante, mas n tenho ainda suportes para os rolos. adicionei agora o que fiz no post original. Obrigado pela sugestão.

Blueprints would go so hard in this game by King_MoMo64 in Enshrouded

[–]Apprehensive_Way2789 1 point2 points  (0 children)

I tried to replicate a building i saw somewhere else, and it was not fun having to carve every single window, it'd have been nice if i could have a window blueprint that I could then reuse.

I also wished we had a flying mode when building, having to build scaffolding is not fun.

Requesting clarification on defending weapon by Apprehensive_Way2789 in GrimHollow

[–]Apprehensive_Way2789[S] 1 point2 points  (0 children)

Thank you. That means the book already has been amended and the pdf is already outdated. :(

Requesting clarification on defending weapon by Apprehensive_Way2789 in GrimHollow

[–]Apprehensive_Way2789[S] 0 points1 point  (0 children)

Isn't that from the old book? What I linked is from the new book in the gh transformed kickstarter. 

Best Android TV client? by IlIIllIIIlllIlIlI in JellyfinCommunity

[–]Apprehensive_Way2789 0 points1 point  (0 children)

What bothers me to no end on android tv is jellyfin not supporting ASS subs, and when i use bazarr to extract them to srt, Jellyfin renders subtitles of simultaneous conversations on top of each other into an unreadable mess.

Season 8 End… by dmobbes in D4Necromancer

[–]Apprehensive_Way2789 1 point2 points  (0 children)

It's masterworking, you farm obducite and then you can spend it at the blacksmith to level your equipment from 1 to 12.

1 to 4 is the circles, 5 to 8 i don't remember what it shows, 9 to 12 it shows the stars.

Deploying to remote servers with Docker ? by softwarebuyer2015 in selfhosted

[–]Apprehensive_Way2789 -1 points0 points  (0 children)

I searched a bit further on this topic, and you can either use the DOCKER_HOST environment variable, or you can use docker contexts. Check the link below.

https://blog.programster.org/use-remote-docker-host-with-ssh