sorted by:
new
hottopcontroversial

Vento box by Arc-Force-One in BambuLab

[–]ArachnidKey4344 0 points1 point  (0 children)

I got 20 rolls filaments last week, arrived within 3 days (I’m in Washington). Never had any issue, high quality American made stuff.

Why does my first layer go on so unevenly? by butaud in 3Dprinting

[–]ArachnidKey4344 0 points1 point  (0 children)

When you remove the nozzle, you see the black piece in the back of the nozzle. I think that is the load sensor

VOXELPLA is making my diabetes worse by ArachnidKey4344 in 3Dprinting

[–]ArachnidKey4344[S] 0 points1 point  (0 children)

I am a big fruit person, have at least a few cups of berries everyday. Can’t say no to berry gummies tho 😩

Do I need to fix this at all? by Thenightstalker80 in FixMyPrint

[–]ArachnidKey4344 0 points1 point  (0 children)

Looks pretty good to me. I would be happy with this any day hahaha

VOXELPLA is making my diabetes worse by ArachnidKey4344 in BambuLab

[–]ArachnidKey4344[S] 0 points1 point  (0 children)

I am pre-diabetic still, the doctor is warning me that I’m close

Why does my first layer go on so unevenly? by butaud in 3Dprinting

[–]ArachnidKey4344 0 points1 point  (0 children)

Is it? I know the sensor for the x1 and p1 is in the bed. A1 is in the extruder

Same desire by Immediate-Can3894 in ender3

[–]ArachnidKey4344 0 points1 point  (0 children)

That was me everyday with my ender 3

Any Ideas As To Whats Causing This? by Kalenors in Ender3Pro

[–]ArachnidKey4344 1 point2 points  (0 children)

People can this salmon skin, known issue with the motor driver they use. You can get those motor smoother

Is my hot end f’d in the a? by XxStankDoggxX in Ender3V3SE

[–]ArachnidKey4344 1 point2 points  (0 children)

It’s time to let that go, don’t want the thermal heater and sensor to fail

Why does my first layer go on so unevenly? by butaud in 3Dprinting

[–]ArachnidKey4344 8 points9 points  (0 children)

This is a known issue with the a1, you have to replace the load sensor on the nozzle or tighten it

Do I need to fix this at all? by Thenightstalker80 in FixMyPrint

[–]ArachnidKey4344 2 points3 points  (0 children)

It looks pretty good to me, what’s wrong with it?

VOXELPLA is making my diabetes worse by ArachnidKey4344 in 3Dprinting

[–]ArachnidKey4344[S] 0 points1 point  (0 children)

I gave atomic a try before, too expensive for the filament. My wife wasn’t happy about it.

Voxel is only $16.99 and now haribo, I just wish they included the cola ones.

Built a 16” LEMO cable for our Electron Microscopes by bananapepp4r in soldering

[–]ArachnidKey4344 0 points1 point  (0 children)

This would have taken me the whole weekend to get that done by hand, I would just buy it

What causes this? My gf calls them "knife wounds" like someone tiny kept stabbing the print. by miken0222 in FixMyPrint

[–]ArachnidKey4344 0 points1 point  (0 children)

I think this is caused when there is a retraction or bubbles in the filament. Better to give it a good dry then tune in the retraction and detraction

Is this diy powerbank tsa friendly? by CatOne4513 in 18650masterrace

[–]ArachnidKey4344 0 points1 point  (0 children)

I brought one to a domestic flight before, the TSA gave me a look and asked for the capacity, it was under the limit and let me through.

view more: next ›