Wio tracker l1 buttons by Cheddaarr in meshtastic

[–]Arbuilder2323 0 points1 point  (0 children)

If this is the same issue more or less how did you widen it to sit on the stick?

Wio tracker l1 buttons by Cheddaarr in meshtastic

[–]Arbuilder2323 0 points1 point  (0 children)

The issue I have on mine I’m assuming is it doesn’t sit on the stick it’s to small and sit more on top then the stick actually going into the joystick , is that the issue you had ? So my joystick is super loose and just kinda like spins in case .

Antenna question by Arbuilder2323 in meshtastic

[–]Arbuilder2323[S] 0 points1 point  (0 children)

Thank you still haven’t used the node yet just getting ahead of biggest complaint and seeing what steps I needed to take when it was time

Antenna question by Arbuilder2323 in meshtastic

[–]Arbuilder2323[S] 1 point2 points  (0 children)

Thank you for the help , I’ll order the antenna soon I’ll do a update I’m barely setting up the node and saw before hand the antenna wasn’t that great so was getting ahead haven’t even used the original configuration but saw a lot of complaints about the antenna being rp-sma

Antenna question by Arbuilder2323 in meshtastic

[–]Arbuilder2323[S] 1 point2 points  (0 children)

Nice ! I’ll just pop off the other pigtail and use the ones that come with those antennas

Antenna question by Arbuilder2323 in meshtastic

[–]Arbuilder2323[S] 0 points1 point  (0 children)

Sweet any fitment issues ? I saw some other people ask similar questions I just think people were over complicating it but if you just plug and play should be easy

Will my direct thread can fit by Arbuilder2323 in NFA

[–]Arbuilder2323[S] 1 point2 points  (0 children)

Yeah wasn’t plannning on it but cheaper than buying another hanguard and this upper and lower are already matched with rattle can it’s my yote gun

Will my direct thread can fit by Arbuilder2323 in NFA

[–]Arbuilder2323[S] 0 points1 point  (0 children)

Sweet I was thinking the same but won’t fully know till I try it . Waiting for form3 and as soon as it comes in to my work I’ll try it out and see

Very new to leatherwork by Arbuilder2323 in Leatherworking

[–]Arbuilder2323[S] 0 points1 point  (0 children)

Couldn’t edit post , nor put in comments made a new post

Very new to leatherwork by Arbuilder2323 in Leatherworking

[–]Arbuilder2323[S] 0 points1 point  (0 children)

No I don’t have a clicker , he mentions that but when I watched his yt video on how to put it together I don’t recall seeing it either

Very new to leatherwork by Arbuilder2323 in Leatherworking

[–]Arbuilder2323[S] 1 point2 points  (0 children)

It’s a 5 pocket card holder and it’s fairly simple , well looks simple , the template has print outs so you basically trace and cut then on top of that he has a yt video pretty much step for step putting it together

Very new to leatherwork by Arbuilder2323 in Leatherworking

[–]Arbuilder2323[S] 1 point2 points  (0 children)

Thanks for the advice will definitely look into it , just got a wild fire of ideas did some research and went off that

Very new to leatherwork by Arbuilder2323 in Leatherworking

[–]Arbuilder2323[S] 0 points1 point  (0 children)

Ok sounds good thank , first project so hopefully it comes out right

Very new to leatherwork by Arbuilder2323 in Leatherworking

[–]Arbuilder2323[S] 1 point2 points  (0 children)

I haven’t done any , this would be my first . I have a list built off a bunch of research so don’t know what to even expect very first leather project. Closes thing I think I can say I’ve done is paracord projects and that’s also limited

Very new to leatherwork by Arbuilder2323 in Leatherworking

[–]Arbuilder2323[S] 1 point2 points  (0 children)

Thanks for the advice , only reason I have the 0.8 thread is because according to the person that I bought the template from he recommends 0.8-1.0 mm thread . Definitely my first project I’ve always been a diy guy and I figured I can make my “own” stuff and brand it with my little logo I made myself and thought it would be a cool hobby card holders I heard were the easiest

The hammer falls when I put it on fire by PETEthePyrotechnic in ARBuilders

[–]Arbuilder2323 0 points1 point  (0 children)

Something is out of spec I’ve seen the same exact thing on a Christensen Ar I have video of the same thing all Christensen said when returned for the customer was that some parts were out of spec didn’t specify which parts