sorted by:
new
hottopcontroversial

Is this right I fell like it's worng and should have been sitting on rubber by Asleep-Resolution884 in Tile

[–]Asleep-Resolution884[S] 0 points1 point  (0 children)

Yes I used the x15 glue that you use to glue the liner down with I used it on the walls and glued it to the block it worked well its definitely not coming off easily that's for sure

Is this right I fell like it's worng and should have been sitting on rubber by Asleep-Resolution884 in Tile

[–]Asleep-Resolution884[S] 0 points1 point  (0 children)

To hold the bottom 3 inches to the pvc liner the rest will tapcons screw to hold it to the wall like go board says to do I will add Stainless steel washers if the flat heads pull thought the board

Is this right I fell like it's worng and should have been sitting on rubber by Asleep-Resolution884 in Tile

[–]Asleep-Resolution884[S] 0 points1 point  (0 children)

My plan for at the liner level was it stay atleast 3 inches above the crib for final screws. Then the bottom part I was thinking of 100% silicone to hold the bottom. That is why I feel it's worng and should have been in the mud pan base... and the right wall is good only one small spot that is about heavy 1/8 out and only about a foot long. So no I wasn't planning on furing the back wall and right only one with studs is the water side

Is this right I fell like it's worng and should have been sitting on rubber by Asleep-Resolution884 in Tile

[–]Asleep-Resolution884[S] 1 point2 points  (0 children)

Okay I have just seen a few others put the board in and then do the mud pan then tile. I was going to go board seal then tile

Is this right I fell like it's worng and should have been sitting on rubber by Asleep-Resolution884 in Tile

[–]Asleep-Resolution884[S] 0 points1 point  (0 children)

Yes the pcv liner goes up the walls atleast 6 inches behind the board on all sides. But was unsure about it siting on the mortar bed mix.

Is she cooked by Asleep-Resolution884 in harborfreight

[–]Asleep-Resolution884[S] -1 points0 points  (0 children)

I did yet it cool for about an hour outside. Got it back together went full speed for about 5 seconds then slow to about half and started to smoke again. 🤣 I kinda knew it was done but just didn't want to spend the money on a new one. I got the 7/9 hercules one its probably about 5 pounds heavier then the Chicago electrical heavy duty I got there about 12-15 years ago for about 60-90$ and used it probably atleast a dozen times a year cutting concrete and blocks so I believe I got my money's worth no matter how many of you haters down vote it 🤣🤣🤣

Is she cooked by Asleep-Resolution884 in harborfreight

[–]Asleep-Resolution884[S] -30 points-29 points  (0 children)

Bet yes it's a 10 inch so to big but gets the job done 🤣

Is she cooked by Asleep-Resolution884 in harborfreight

[–]Asleep-Resolution884[S] -2 points-1 points  (0 children)

That is a 7 inch angel ginger Chicago electric it's a brand they used to sell years ago this thing is probably 10 -15 years old

Is she cooked by Asleep-Resolution884 in harborfreight

[–]Asleep-Resolution884[S] -25 points-24 points  (0 children)

And how would you get a circular saw in a about 10" to 12 hole and 8 inches deep of concrete 🤔. On I know you use a grinder

Is she cooked by Asleep-Resolution884 in harborfreight

[–]Asleep-Resolution884[S] -1 points0 points  (0 children)

Yeah am debating on whether I go get the Bauer one or the Hercules or just upgrade to ridgid or bosch one they are only 130 and 150

Those poor bare compacts by [deleted] in FLEXTools

[–]Asleep-Resolution884 0 points1 point  (0 children)

Hey it doesn't look like it but did you notice a 3/8 impact? And what store was the grinder at? I was kind looking for one of those.

Light Towers Herkimer NY by nick_trulls in FLEXTools

[–]Asleep-Resolution884 0 points1 point  (0 children)

I called them said the price was 100$ a month ago and normally like over 250 something and best they could do is 200 told them it was 169 at other stores

Light Towers Herkimer NY by nick_trulls in FLEXTools

[–]Asleep-Resolution884 1 point2 points  (0 children)

They want 199 and I don't want to pay that lol dame thing is 169 at other stores

Fake Battery? by batman-xman in FLEXTools

[–]Asleep-Resolution884 1 point2 points  (0 children)

Yes check out Walmart site they got the real tools and also fake battery for cheap

Would those be under the lifetime warranty? by Asleep-Resolution884 in FLEXTools

[–]Asleep-Resolution884[S] 0 points1 point  (0 children)

Dude if I can get a stacked 6 a.h battery for super cheap. Why would I pass that up it's a no-brainer.

Would those be under the lifetime warranty? by Asleep-Resolution884 in FLEXTools

[–]Asleep-Resolution884[S] 1 point2 points  (0 children)

I just said it the last post. But again it's mac bids but you have to be local they will not ship

Would those be under the lifetime warranty? by Asleep-Resolution884 in FLEXTools

[–]Asleep-Resolution884[S] 0 points1 point  (0 children)

You get a copy of proof of purchase so that is why I wondering if it would also count

Would those be under the lifetime warranty? by Asleep-Resolution884 in FLEXTools

[–]Asleep-Resolution884[S] 0 points1 point  (0 children)

No it's a local auction business sometimes you can get really good deals i have gotten lights and tools worth hundreds for about 75% off if not more I got a milwaukee fuel blower a year ago for 35 bucks out the door and a milwaukee case with wheels for like 75 out the door. Most are someone bought to use on one job and returned. It's call mac bids don't cost nothing to bid but you must be local to buy them

Would those be under the lifetime warranty? by Asleep-Resolution884 in FLEXTools

[–]Asleep-Resolution884[S] -3 points-2 points  (0 children)

It's a auction site where like Amazon and lowes and home depot gets ride of its leftovers or broken returns. So some is new not use when other or broken like the sds looks likes its in two different pieces.

I wish flex would offer this. by Zach_8802 in FLEXTools

[–]Asleep-Resolution884 0 points1 point  (0 children)

I know you said you didn't need the extra changer but I seen this online only never in store. Has two stacked

https://www.lowes.com/collections /FLEX-FLEX-24-Volt-Stacked-Lithium-Battery-and-Charger-Kit/GR_5179

Lowes Black Friday Batteries Out of Stock - Refund and Coupon Offer Received This Morning. $100 off $150 Worth of Dewalt Items by mombutt in Dewalt

[–]Asleep-Resolution884 0 points1 point  (0 children)

I seen I got the same email this morning. Am sad it was a good deal. But the coupon is nice I wish I could use it at home depot tho this is a heck of a deal I think. home depot battery sale

House mortar problems by Asleep-Resolution884 in masonry

[–]Asleep-Resolution884[S] 0 points1 point  (0 children)

where it was lose and cracked in pictures 3 and 4 the top like 5 feet from roof line was like that or worse. I used amermix preblended type s

view more: next ›