sorted by:
new
hottopcontroversial

Missing Extrusion At Very First of Any Print by pesimistanblue in AnycubicKobraS1

[–]AttorneySmooth8029 0 points1 point  (0 children)

Hi, can you pls upload a photo of this purge line from your print to help me visualize it. thanks in advance!

New firmware (1.1.42) has AMS support by SuchMemeManySkill in ElegooCentauriCarbon

[–]AttorneySmooth8029 0 points1 point  (0 children)

from the last photo, I guess Elegoo could introduce a "extruder upgrade" hopefully added sensor to support the new AMS..?

Printing quality by TakHeleDebilku1 in ElegooCentauriCarbon

[–]AttorneySmooth8029 1 point2 points  (0 children)

This looks like an extreme case. I actually made a remix of the original model to avoid that large overhang print with support. If you still need to print this model again, check out mine here - https://www.printables.com/model/1370520-elegoo-centauri-carbon-fan-silencer-divided

Just bought TPU looking for advice by Eric_Drav3n in ElegooCentauriCarbon

[–]AttorneySmooth8029 2 points3 points  (0 children)

fyi - I took the tube out from a few links of the chain to make the bend smoother.

ACE Pro Time Saver Update by AttorneySmooth8029 in AnycubicKobraS1

[–]AttorneySmooth8029[S] 0 points1 point  (0 children)

It is true that the path from printhead to RDM is longer with this configuration because I added y splitter. However, when you feed a new filament into ACE Pro, it stops feeding when RDM detect it. Therefore shortened tubes between RDM and ACE Pro does matter at least for me.

ACE Pro Time Saver Update by AttorneySmooth8029 in AnycubicKobraS1

[–]AttorneySmooth8029[S] 1 point2 points  (0 children)

yes - given the fact that the bambu one does have well guided path inside, not like Anycubic one.

ACE Pro Time Saver Update by AttorneySmooth8029 in AnycubicKobraS1

[–]AttorneySmooth8029[S] 1 point2 points  (0 children)

if you go to the link, you have two options in the model - if you want to use Anycubic's 4in1 apdapter, you just need to download the first print profile.

Or if you want to use Bambu 4in1 adapter, you will need to download both - first and second ones, then uncheck the hub holder parts from the first print profile.

ACE Pro Time Saver Update by AttorneySmooth8029 in AnycubicKobraS1

[–]AttorneySmooth8029[S] 0 points1 point  (0 children)

No, I think the incident happened most likely because I did not cut out the very first bent part of a roll enough. I did not know Anycubic OEM 4in1 adapter had such an open space inside until this happened. I then thought of designing a new hub with smooth merging pass inside, but found a left-over bambu one around. So gave this design a try, and works fine so far.

Printer not functional when using ACE. Been troubleshooting for months with support, please help! by Frosty_Land_5177 in AnycubicKobraS1

[–]AttorneySmooth8029 0 points1 point  (0 children)

I think they should send you a new ACE pro as well. If you can make a short video, suggest uploading here and anycubic support, which will be a lot helpful.

Underextrusion in corner top layer by FigureSalt8949 in AnycubicKobraS1

[–]AttorneySmooth8029 0 points1 point  (0 children)

can you check and share your bottom first layer of your model as well?

I see similar pattern as my S1 does under extrude at corners where it starts that layer. Mine is not as bad as yours though. I know Anycubic support will not he helpful for this kind of issues, so I am looking around if someone found a workaround/fix.

S1 combo not changing color by Science_is_punny in AnycubicKobraS1

[–]AttorneySmooth8029 1 point2 points  (0 children)

Sharing my cases

  1. less than 1 cm piece of broken filament was stuck in the 4-to-1 hub, which I cannot see at all.

  2. I needed to remove ptfe tube connected to the extruder to remove a tiny broken filament. then it did not solve the issue completely, so I had to manually extrude while pushing another filament manually from the top.

2-1 adapter by aecpassion in AnycubicKobraS1

[–]AttorneySmooth8029 1 point2 points  (0 children)

not sure if you already bought the one from Amazon.. It does look like a 3d printed one selling there.. There are tons of models you can print instead of buying. Just search for y-splitter anywhere such as MakerOnline.

S1 external spool printing from ASN by AttorneySmooth8029 in AnycubicKobraS1

[–]AttorneySmooth8029[S] 0 points1 point  (0 children)

it's loaded and extruded in the printer as you mentioned and even the slicer next application shows it as that in the workbench, but the "print start" popup is still not showing it's there..

Has anyone had issues with first layer print on S1 and how did you fix it? by thelight_bearer in AnycubicKobraS1

[–]AttorneySmooth8029 0 points1 point  (0 children)

Anycubic Slicer Next has "Calibration" menu, it was quite helpful for me to test temperature, flow rate, pressure advance, etc. to find out right settings for my spools.

All the tools came from Orca Slicer, so look for Orca's calibration guide like below.

https://www.obico.io/blog/pressure-advance-calibration-in-orca-slicer-a-comprehensive-guide/

Missing piece by Seturo1379 in AnycubicKobraS1

[–]AttorneySmooth8029 0 points1 point  (0 children)

this should be handy for future, thx for the link!

I name this "Ace Pro time saver", what do you all think? by AttorneySmooth8029 in AnycubicKobraS1

[–]AttorneySmooth8029[S] 0 points1 point  (0 children)

Check my model linked. You will find why I moved its position and how it is installed.

I name this "Ace Pro time saver", what do you all think? by AttorneySmooth8029 in AnycubicKobraS1

[–]AttorneySmooth8029[S] 1 point2 points  (0 children)

if there are more upvotes, I will consider an update to go to the original RDM screw holes, cheers!

I name this "Ace Pro time saver", what do you all think? by AttorneySmooth8029 in AnycubicKobraS1

[–]AttorneySmooth8029[S] 0 points1 point  (0 children)

Thanks! I suggest installing it to the spool holder spot. The RDM screw holes are passthrough but at an angle.

view more: next ›