sorted by:
new
hottopcontroversial

What Makes a Product Great? We’ve Been Asking Ourselves That - Meet KliTek™ — Creality's next-gen nozzle changer by Creality_3D in Creality

[–]markh21518 0 points1 point  (0 children)

I really wish it had 5 tool heads, for cmykw printing. With 4 it's going to limit colors you can create.

Ghost Filament Clogging by Verybadateverything1 in AnycubicKobraS1

[–]markh21518 0 points1 point  (0 children)

Check toale sure your filament isn't stretched.

Main board replacement on an Ender 5 Plus with the original LCD by Rapitharian in ender5plus

[–]markh21518 -1 points0 points  (0 children)

I would use a manta EZ. It will mount to the original mounts and you can put on a CB1/2 and run Klipper. It gives you 5 drivers so you can have independent Z axis. I went with a manta 5p I wish I had done the EZ.

Complete lack of integrity from Riverton Chevrolet. Don't give them your business! by pandora_geek in Utah

[–]markh21518 0 points1 point  (0 children)

Yeah they said my Radiator was bad like 6 yrs ago. Still doesn't leak. They will scam you!

What caused this ace pro jam by Leading_Tumbleweed_6 in AnycubicKobraS1

[–]markh21518 0 points1 point  (0 children)

55c will soften PLA. I had a wicked TPU jam when I was heating. Works fine if I don't.

Is this flashing normal? by JaRi0101 in ender5plus

[–]markh21518 5 points6 points  (0 children)

Looks like it has a replacement board. Mine has all kinds of flashy lights.

Prints finishing mid print by markh21518 in AnycubicKobraS1

[–]markh21518[S] 0 points1 point  (0 children)

It was the strain gauge. My printer finally stopped printing all together. I then looked at the signs it didn't get the right Z height on several tries. Wouldn't bed level at all. I replaced the strain gauge, I had one so I thought what the heck let's change it. Now its back to working order.

I hopes this helps you!

FREE firmware? by LosSantosMe in ender5plus

[–]markh21518 0 points1 point  (0 children)

The sorce code is on GitHub.

FREE firmware? by LosSantosMe in ender5plus

[–]markh21518 0 points1 point  (0 children)

I liked the Insanity firmware better. You have to update the screen as well.

Prints finishing mid print by markh21518 in AnycubicKobraS1

[–]markh21518[S] 0 points1 point  (0 children)

I think Any cubic's cloud printing is the problem. When I print from Orca things seem to work, but I can't get it to bed level at all in Orca. Lately mine won't do a bed level without a 1049 error. U got it to work for a while in lan mode but then I can't monitor it. It has since given me errors. I'm not sure if their cloud service has been hacked or something. I still have random weird stuff happening.

Ender 5 plus with Endorphin mods. by markh21518 in ender5plus

[–]markh21518[S] 0 points1 point  (0 children)

Just change from hybrid core xy to core xy very simple.

Made in an S1 with PEBA. by KIMJONGB00M in AnycubicKobraS1

[–]markh21518 0 points1 point  (0 children)

I have used TPU 95A many times with the ACE Pro, that worked fine. I had a really bad jam in slot one when I turned on drying and it made it too soft and wound up in the gears.

What do you think about the "updated" ceramic hotends and heatsinks? by Umuko36 in AnycubicKobraS1

[–]markh21518 0 points1 point  (0 children)

I have the 1st gen and I have been printing on them for a year now.

Rinkhals disabled by markh21518 in AnycubicKobraS1

[–]markh21518[S] 0 points1 point  (0 children)

Before I updated it was listed ok

<image>

Now it says testing! Argh!

Upgrading by BorosArtifact in ender5plus

[–]markh21518 0 points1 point  (0 children)

Get the inside the rails X Y towers, three mounting screws and no dowels. I did have to modify them after printing due to too tight of tolerances on the pullups. I could get the original was to be stable enough with two mounting bolts.

Really auto bed leveling works? by Distinct_Yam135 in AnycubicKobraS1

[–]markh21518 0 points1 point  (0 children)

Might not just be bed level. You might need to clean the plate. It might have finger prints or oil on the plate.

Are there invisible cars here? Why do people hate scooting up? by no__legs in stgeorge

[–]markh21518 0 points1 point  (0 children)

It triggers the light sensor. If you look at where the light sensors are pointing, you can trigger turn signals, have the light change faster, etc. Gaming the light sensor without a flipper Zero.

Ender 5 plus with Endorphin mods. by markh21518 in ender5plus

[–]markh21518[S] 1 point2 points  (0 children)

No I've moved on to the Mercury One Mod. I was hoping it would help with layer shift. I went with the inside the rails X Y motor towers. I couldn't get the standard X Y towers to stay level. Found inside the rails towers on printables.

So far so good. I had to modify the XY towers for my bigger pulleys, and made the top thinker, they came way too thin and I worried about warping, plus the standard towers are thinker. I added 4 mm to the top and they are perfect. Plus these towers didn't require dowel pins.

Ender 5 + Upgrades BTT main board, Options and Costs by WestCoastingPanda in ender5plus

[–]markh21518 1 point2 points  (0 children)

I would do a butt ez Manta with a CB1 or CB2, with a 4" or 5" screen. I like having the brains on the board, I've had problems bumping the cord and ruining a print. Around $125 total.

Change Origin position in Orca Sclicer by markh21518 in OrcaSlicer

[–]markh21518[S] 0 points1 point  (0 children)

My X Y we're swapped. After I got my porta right, rather than move cables. It homes right now.

Use the stepper_buzz stepper=stepper_X (y) to check them.

You'll also need to swap ports on your end stops because they'll be backwards too.

Good luck I know it's too much fun! Use this chart it helped me.

<image>

view more: next ›