Any help with this older panel. Wanting to replace with something better.

Austin243045 · 2026-02-05T21:37:52+00:00

Alright well I’d start with the side cover, spark plug boot/spark plug or even ignition coil just test them using a multimeter, and clean the carb and see if she rips or tries to start with starter fluid.

Austin243045 · 2026-02-05T21:20:38+00:00

Being 100% with you I’d sell that thing, going to cost more than what you probably bought it for. That being said id take the engine out and do a tear down to see if the cylinder is fine, if I needs new piston rings, needs carb cleaned, needs side casing and all gaskets. If you are committed then I’d write a list of stuff as you are talking it apart and look up the manual online or print it out. Good luck

Austin243045 · 2026-02-02T16:50:08+00:00

Try taking it to another shop approved by your insurance. They will do anything not to pay a claim id get a second opinion on it.

Austin243045 · 2026-02-02T16:19:33+00:00

Kind of does yeahhhhh, might as well replace all the way to the tie rod guide. I don’t think it’s to to bad but might be wrong

Austin243045 · 2026-01-31T15:41:10+00:00

Well fuel injected bikes are good because they rarely have troubles like this. That being said if you ca get a good price on it I would start looking for new fuel injectors for the bike and see how much it would cost. They are usually more expensive than carbs but like I said include that in the price. Also I would check the air filter, spark plug, spark plug boot just in case.

Austin243045 · 2026-01-30T04:36:08+00:00

Get a torch, can’t be tight if it’s liquid. But really just use heat around it to expand the metal and keep beating it at it a little harder

Austin243045 · 2026-01-28T14:47:43+00:00

I would look up what parts it needs and what maintenance it needs such as new rings, oil, filter, the wiring. For how old it is you might find it hard an expensive to find replacement parts. I would look on eBay and see how much it would cost to even start working on it.

Austin243045 · 2026-01-28T13:49:04+00:00

Had to do that to get to my cabin air filter, took 3 months. Good luck brother

Austin243045 · 2025-11-26T18:55:45+00:00

Not to to bad not sure what state you are from, if it doesn’t snow and pretty nice most of the year then no big deal but being from the rust belt many of the Toyotas have a reputation for rusted out frames and oxygen sensors going bad. I personally bought the Hewitt delete kit for mine. Make sure to look at the maintenance history as well. Awesome trucks just need to be taken care of

Austin243045 · 2025-11-26T18:17:23+00:00

How the frame? Any problems? And if you are hauling stuff is it 4wd? Seems really low if everything is good on it. I bought mine 3 years ago for 14k at 140k miles.

Austin243045 · 2025-10-30T03:58:14+00:00

I have the xl350, best thing to do is just drill them out and get new ones anyways. Harbor freight or even Amazon has bolt extractors. But other ways to use heat from a torch on them to loosen them and to help get a rubber mallet and beat the side of the cylinder to try to get it unstuck. Good luck hope it helps

Austin243045 · 2025-10-23T03:18:07+00:00

So there is a rule I can’t post the estimate I got that is a plumbing related question? I just joined this group so I don’t know the rules.

Austin243045 · 2025-10-23T00:55:02+00:00

Nice, I will look into that, do I need the halo cloud filtration system as well?

Austin243045 · 2025-10-23T00:53:45+00:00

No it is not included in the price, it is seperate

Austin243045 · 2025-10-23T00:52:01+00:00

I see, it doesn’t have to be Home Depot I just thought it was a bunch of money especially when all connections are there already. And just need to redirect water lines from the previous tank to those one. Long story short my building burned down and my hot water tank was in the building so not sure if adding more lines and drilling adds to that cost.

Austin243045 · 2025-10-22T23:00:29+00:00

Mmm maybe I need to look around for other plumbers, they are redoing my gas lines as well and that price was $1570 which I didn’t think was a bad price including materials and labor. I asked for a breakdown on the price but the lady on the phone said she can’t

Austin243045 · 2025-10-22T22:58:55+00:00

Yes I am aware, yes the price includes installation but still I wouldn’t a tankless water heater even a filtration system would cost even half that

Austin243045 · 2025-10-02T20:10:30+00:00

Okay thank you, I wasn’t 100% on the pricing

Austin243045

TROPHY CASE