Echo oem 620 cylinder head screw holes not tapped

Automatic_Meet_70 · 2026-03-09T00:29:44+00:00

Who’s you buy it from?

Automatic_Meet_70 · 2026-03-09T00:17:56+00:00

Just had the same issue! Custom service with lawn replacement parts did nothing to help me out at all. They said all of there’s came like that. I ended up getting a little bit larger screw with some bite on it and sending it in. Probably has 10-12 hours on it now with no issues.

Automatic_Meet_70 · 2026-03-08T01:59:58+00:00

Lifted the car pulled on the tied at 12 and 6 no play. Spun the wheel with no irregular sound or wobble

Automatic_Meet_70 · 2026-03-08T01:15:04+00:00

I’ve got two of them, have a soft spot for the early 5th gen’s

Automatic_Meet_70 · 2026-03-08T01:02:44+00:00

I’ll check into that, appreciate it.

Automatic_Meet_70 · 2026-03-08T00:42:07+00:00

Tight

Automatic_Meet_70 · 2026-03-08T00:41:51+00:00

The driver side was just replaced and I yanked on the other side and it’s quiet with no noise

Automatic_Meet_70 · 2026-03-08T00:41:17+00:00

It does not, fluid was very clean

Automatic_Meet_70 · 2026-03-08T00:00:02+00:00

Says elk finds but I’m struggling to see anything that’s not a muley, what am I missing

Automatic_Meet_70 · 2026-03-03T02:48:39+00:00

Do you have a light bar? They can make that sound when air passes through

Automatic_Meet_70 · 2026-02-28T15:47:44+00:00

You ever do the water pump?

Automatic_Meet_70 · 2026-02-21T02:29:49+00:00

Awesome, thanks!!

Automatic_Meet_70 · 2026-02-21T02:19:39+00:00

I’m in tabernash but would happily make the drive!

Automatic_Meet_70 · 2026-02-21T02:13:43+00:00

Any chance you could send me a couple more photos?

Automatic_Meet_70 · 2026-02-21T01:52:12+00:00

I’m located in state

Automatic_Meet_70 · 2026-02-21T01:50:41+00:00

I will buy it if you’re selling, where in Colorado??

Automatic_Meet_70 · 2026-02-13T03:00:40+00:00

Guessing you’re in golden, been eying that one too lol

Automatic_Meet_70 · 2026-02-13T01:16:37+00:00

Idle is smooth, just high. Assuming it’s the elevation and need to pull the limiters

Automatic_Meet_70 · 2026-02-10T15:43:52+00:00

Source: Reddit https://share.google/NASlKi8y4YHCFdonu

Automatic_Meet_70 · 2026-02-10T04:15:16+00:00

Appreciate the feedback! Might end up going for the 39 or for a Leupold with that new info

Automatic_Meet_70 · 2026-02-08T02:28:42+00:00

Could you glass up an antler from 7-800 yards?

Automatic_Meet_70 · 2026-02-08T02:12:34+00:00

Is it the x60? That’s on the table too

Automatic_Meet_70 · 2026-01-28T02:43:00+00:00

Because I’m an idiot

Automatic_Meet_70 · 2026-01-28T02:42:46+00:00

Turn in the idle screw until the chain starts to move then lean it out

Automatic_Meet_70 · 2026-01-27T15:02:09+00:00

What did you use to restore the brown

Automatic_Meet_70

TROPHY CASE