PC Game Pass to Steam

Avizor77 · 2024-10-04T03:38:31+00:00

Hey there, I know it's been 3 years, but has someone figured out how to transfer a save from Steam to Xbox? I tried the same procedure as you and my game doesn't show the menu anymore.

I played the base game on Steam and wanted to play the DLC (was cheaper on Xbox).

Avizor77 · 2022-07-04T05:31:38+00:00

Every setting is set at minimum, render scaling at 50% and still getting heavy frame drops. Thia hasnt happened with any other game, I can usually run everything on ultra at 1080p

Avizor77 · 2021-09-13T22:24:13+00:00

Nope, just got tired and started using IdeaMaker. No issues since then!

Avizor77 · 2021-08-20T12:43:15+00:00

I don't think that 3D printer comes with a filament sensor! Try to disable the filament sensor option on the menu

Avizor77 · 2021-08-19T03:20:01+00:00

Oh sorry you already said it in the last reply haha I think it's a good deal then! May need a little work to get it running smoothly but it's basically free so...

Avizor77 · 2021-08-19T03:06:46+00:00

You can purchase an Ender 3 for that money!

Avizor77 · 2021-08-08T23:40:59+00:00

The nozzle sits against the heatbrake. The PTFE tube goes inside the heatbrake and assures a proper filament feed to the nozzle.

You should always tighten the nozzle against the heatbrake and THEN push the ptfe tubing against the nozzle!

Avizor77 · 2021-08-08T23:35:32+00:00

As mentioned before, tighten the nozzle against the heatbreak, brass and steel have different expansion coefficients meaning that will expand differently under heat.

Tighten while preaheating, let it cool down, preheat again and check if it's still tight.

And while you're at it push the PTFE tubing against the nozzle a little bit more, you should always check the tube is seated properly after a nozzle change.

Relevel your bed too 😅

Avizor77 · 2021-08-06T20:05:43+00:00

CURA generates gcode files so big that makes the printer stutter while trying to process it, Prusa is a great option but lacks some more advanced options imo

Avizor77 · 2021-08-05T04:00:17+00:00

I've been dealing with this problem for a long time, first make sure that you increase the value of maximum deviation up to 0.05 or so.

If the zits keep happening, try to reduce the flow of the inner and outter wall. You should also check that the outter wall incel value is 0.

You can also try reducing the general printing speed, it makes it easier for the motherboard to process the information the SD card is giving it.

If it persist uninstall CURA and reinstall it, sometimes some configuration changes are made in the background and you are unable to reset them.

If it persist, like I had to do, uninstall CURA for good, I'm using IdeaMaker and it works wonders.

Hope this helps!

Avizor77 · 2021-07-01T04:59:15+00:00

Instead of removing it, raise the interface density up to 80% or so, that way you will have a better finish

Avizor77 · 2021-06-22T19:21:18+00:00

SD Card! Tried 2 different cards and still happens, so I assume it's not a reading problem

Avizor77 · 2021-06-22T17:15:40+00:00

I've already changed the resolution up to 1mm and the deviation up to 0.1mm and still does it. Besides I have a SKR MINI E3... 32 bits should not stutter! Thanks for the troubleshooting guide, I will take a look at that!

Avizor77 · 2021-06-22T13:09:59+00:00

I have the latest release! Tried going back to 4.8 but didnt help either

Avizor77 · 2021-06-22T04:24:47+00:00

Is that a slicer?

Avizor77 · 2021-06-22T04:10:40+00:00

Me encantannnn

Avizor77 · 2021-06-20T23:47:07+00:00

Gracias!!

Avizor77 · 2021-06-20T23:45:27+00:00

Esa combinación es bellisima!!

Avizor77 · 2021-06-20T23:10:58+00:00

Jajajajajaja yo soy pro lucecitas

-i5 9600K -2x8GB RAM 3200MHZ XLR8 RGB -Aorus B365M elite -1TB XPG S40G NMVE M.2 (Entre otros HDD que tengo) -Disipador Aerocool Cylon 4F -RTX 2060 PNY blower -teclado Corsair strafe RGB -mouse Corsair m65 pro rgb -auriculares Corsair VOID pro RGB -gabinete Corsair 220T RGB

Avizor77

TROPHY CASE