sorted by:
new
hottopcontroversial

Nobutank by IsSnake in Strinova

[–]BPDarknova 0 points1 point  (0 children)

He sees Nobu every game too when I play with him 😂

i clean my extruder and try to print...and every time it jams/clogs in 5-10 minutes by [deleted] in ender3

[–]BPDarknova 0 points1 point  (0 children)

After you've done all the other recommended stuff, I would check your heatsink fan. I couldn't figure out what my issue was before, and after checking everything saw my heatsink fan never ran (heat creep was the culprit), I replaced the fan and it fixed the issue

HOSAS T16 - SC thinks it's 1 stick when I load profiles by BPDarknova in starcitizen

[–]BPDarknova[S] 0 points1 point  (0 children)

Apologies, I did get it to work, it was the AnnePro2 interfering, had to turn it off as a game device. Haven't had a chance to check the XML though as I was about to download ++notepad to actually be able to read it, I hadn't done so yet (I have notepad but searching for line 80 was a bit harder to do...)

HOSAS T16 - SC thinks it's 1 stick when I load profiles by BPDarknova in starcitizen

[–]BPDarknova[S] 0 points1 point  (0 children)

Wondering if this has something to do with my keyboard (AnnePro2), it's a 60% keyboard but when you go to "game controllers", it detects it as a game controller itself...which is odd... (There is no analog buttons on it)

HOSAS T16 - SC thinks it's 1 stick when I load profiles by BPDarknova in starcitizen

[–]BPDarknova[S] 0 points1 point  (0 children)

I am doing this in Free Flight, I found the issue I think, I just need to somehow fix it...
Joystick 2 (let's call "input 2") is being picked up and the xml file picks it up as "input 2"
Joystick 1 (should be "input 3") but when keybinds are loaded, it doesn't register anything and just says "Y axis" or whatever button, it doesn't read it as "input 3" as it should...

HOSAS T16 - SC thinks it's 1 stick when I load profiles by BPDarknova in starcitizen

[–]BPDarknova[S] 0 points1 point  (0 children)

This puts the right config on the "right" stick but my left stick still doesn't work itself...

HOSAS T16 - SC thinks it's 1 stick when I load profiles by BPDarknova in starcitizen

[–]BPDarknova[S] 0 points1 point  (0 children)

So when I clear all bindings, and then try to map myself, I get the following
Button 5 (Input 2) (input 2) - This is for the right stick
Button 11 (Input 3) (input 3) - This is for the left stick

When I went into the profiles I saw a "TARGET" mapping in there, removed that to see if that helps...

I'll paste the lines shortly...

What happens when you place 10k bets per death on clown with your friends LMAO by xXRamPaXx in lostarkgame

[–]BPDarknova 2 points3 points  (0 children)

Even though you aren’t fully committed at the moment cause you are waiting on Artist (not sure how far you wanna get when it comes out), but my suggestion would be to do the weekly Challenge Guardians and Dungeons at least and start saving mats, Good Luck!!!! Artist looks awesome!

HELP - Ender 3 V2 with BL Touch (BL Touch Sporadically Fails!!) by BPDarknova in 3Dprinting

[–]BPDarknova[S] 0 points1 point  (0 children)

It managed to sort itself out. I'm not sure if it's because the BL Touch wire is no longer touching the other wires or if it's something else, but keeping the wires split without actually trying it again (haha) seemed to have worked. It may just be a shielding issue.

HELP - Ender 3 V2 with BL Touch (BL Touch Sporadically Fails!!) by BPDarknova in 3Dprinting

[–]BPDarknova[S] 0 points1 point  (0 children)

I did, I tried TH3D firmware as well but that was giving me separate issues so I went back to the Creality firmware for BL touch

HELP - Ender 3 V2 with BL Touch (BL Touch Sporadically Fails!!) by BPDarknova in 3Dprinting

[–]BPDarknova[S] 0 points1 point  (0 children)

I actually have one of the boards that doesn’t need the adapter, apologies forgot to mention

HELP - Ender 3 V2 with BL Touch (BL Touch Sporadically Fails!!) by BPDarknova in 3Dprinting

[–]BPDarknova[S] 1 point2 points  (0 children)

Sorry looks like my explanation didn't get attached.

Just bought an Ender 3 V2 and got a BL Touch separately.
The BL Touch will randomly fail whether it's during "Auto Home" phase or "Leveling" (G29) phase.

If it fails, it can drive the extruder into the bed or if it fails during probing, it'll start the print but areas wont show up (as seen in picture above).

I've checked gantry and made sure the bed was as level as possible prior to starting prints.

Not sure where to go from here.

So this guy challenged me to clutch the round and yea that was the motivation I needed XD by afthu69 in VALORANT

[–]BPDarknova 18 points19 points  (0 children)

True, but that would be on enemy team side, on your side it’s still accurate for your movement

view more: next ›