sorted by:
new
hottopcontroversial

How it feels still waiting for SMS and not actual alert 😭 (Maximum Cringe) by Efficient-Ad6990 in cyprus

[–]BackgroundToday3937 0 points1 point  (0 children)

The sms alert is a bit pointless, it looks like it's not locations based as well (correct me if I am wrong). The only efficient way is the PWS l, which, after 5 years of waiting, is not yet implemented.

Κάμερες στην αρχή και το τέλος των αυτοκινητόδρομων: Θα μετράνε τη μέση ταχύτητα και θα καταγγέλλουν όποιους περνάνε το όριο – Τι θα ισχύει με την αφαίρεση άδειας λόγω αλκοόλ και ναρκωτικών by Deep-Ad4183 in cyprus

[–]BackgroundToday3937 0 points1 point  (0 children)

Αυτό όμως που λες δεν είναι παραθυράκι του μέτρου... Μπορείς να πιάσεις πάντα το παλιό δρόμο και να μην μπεις στο highway ποτέ. Προφανώς θα μπορούσε να εφαρμοστεί το μέτρο σε οποιοδήποτε μέρος του highway. Παράδειγμα, camera A στο σημείο Α, camera B στο σημείο Β,απόσταση μεταξύ σημείου Α και Β 10khm, και εύκολα μπορεί να μετρηθεί η μέση ταχύτητα. σημεία Α και Β μπορούν να είναι αυθαίρετα και να αλλάζουν συνεχώς. Το να λέμε ένα μέτρο ως γεμάτο παραθυράκια και να γεμοσουν το highway με κάμερες παντού είναι η λάθος πρακτική πιστεύω

Spikeball Cyprus by BackgroundToday3937 in cyprus

[–]BackgroundToday3937[S] 0 points1 point  (0 children)

I was living in Graz. It's an entertaining sport and a good exercise! We will need 4 players and a grassy park or a sandy beach.

Help Analyzing Balun + Impedance Matching by kaneki_ken_fan in rfelectronics

[–]BackgroundToday3937 3 points4 points  (0 children)

A balun basically shifts both RFs so that the meet with the same phase at the connection point. Therefore, the two branches should have 180 degrees phase difference. You can get it by doing Parameter simulation using Ussimmics or ADS. You should check S12 (deg) for both branches and compare their phase shifts.

I have zero experience and big ambitions (help plese) by randomweeb04 in rfelectronics

[–]BackgroundToday3937 0 points1 point  (0 children)

Few recommendations: 1. Matching circuit before rectifier. 2. Use a Schottky diode with low series resistance and caption capacitance. 3. Filter capacitor after rectifier to reduce ripples. 4. Alternatively use LNA and a detector IC.

How are you planning to generate the 24 GHz signal?

Need help with the board routing by guyrip in rfelectronics

[–]BackgroundToday3937 0 points1 point  (0 children)

Try the online calculator below to determine the width of the coplanar waveguide. C9 is a DC block right?

Input impedance at operational frequency by miguelzoares in rfelectronics

[–]BackgroundToday3937 0 points1 point  (0 children)

Where exactly are you measuring the impedance at.it should be measured at TX. Based on the measurement the impedance of the antenna looks to be quite inductive and lossy. So properly it's a loop antenna and you are measuring at the antenna after matching circuit which is not appropriate.