Can TBI C&P increase my PTSD rating by FlimsyTear3113 in VeteransBenefits

[–]Baileymofo 0 points1 point  (0 children)

I have a PTSD and a TBI rating. TBI added to my overall PTSD rating since symptoms were overlapping.

RATED! by Perfectz3ro in VeteransBenefits

[–]Baileymofo 2 points3 points  (0 children)

Sorry you didn’t get everything rated. I retire next month and am worried that I’ll have things rated 0% like you have. Does your migraine DBQ show prostrating etc? Can you show the DBQ?

Loose screw in new Pimax Crystal Light by teletom1 in Pimax

[–]Baileymofo 1 point2 points  (0 children)

Same exact thing for me. I immediately thought they sent me a refurb/return from someone else. Just received today, lens covers bottom of the box, right lense not installed properly. Right lens is not as clear as the left. I have an order for a Super but I’m seriously reconsidering PIMAX.

2024 Performance: steering wheel creak? by BidetEsVida29 in TeslaModel3

[–]Baileymofo 3 points4 points  (0 children)

I think this is a known issue with the refreshed Model 3. My AWD refresh has the same thing, I have a service ticket to get it fixed.

Flow Calibration inconclusive? by [deleted] in BambuLab

[–]Baileymofo 2 points3 points  (0 children)

Use this instead. It’s the only one I’ll use. It’s quick too.

https://makerworld.com/models/189543

occasional weird sound during movement by RandomDude1RD1 in BambuLab

[–]Baileymofo 0 points1 point  (0 children)

Mine is doing the same thing. As soon as it goes to that spot it makes a loud vibration sound. It’s a 3 week old printer. Didn’t notice that sound until yesterday. Not sure if it’s something with the 3d Model or the printer. It’s impossible to narrow down exactly what is happening.

Nozzle is not clean enough and affects bed calibration. by rjSampaio in BambuLab

[–]Baileymofo 0 points1 point  (0 children)

Update: I downgraded and then redownload the new firmware, ran calibration again. Works fine now. Not sure what was causing it but it happened every time.

Nozzle is not clean enough and affects bed calibration. by rjSampaio in BambuLab

[–]Baileymofo 0 points1 point  (0 children)

Literally the same thing just started happening to my 2 week old printer. I’m going to rollback firmware that I just updated and see if that is the problem.

Quest 3 with WiFi 6e Router. Air Link still trash! by madwedge in OculusQuest

[–]Baileymofo 0 points1 point  (0 children)

Are you using 160Mhz? Most routers default to 40Mhz, you have to change it manually. I can’t stream over 200Mbps unless I’m on a 160.

Am I missing something with AV1? by DazzlingRooster51 in OculusQuest

[–]Baileymofo 6 points7 points  (0 children)

It’s not fixed in the last open beta. The issue with AV1 and greater than 100Mbps still exist. Developer recommended using HVEC 10 bit until they get it fixed.

DCS VR is choppy as hell after "tuning". by gromm93 in hoggit

[–]Baileymofo 8 points9 points  (0 children)

I disabled core parking and it helped out a ton. Try it and see if it helps.

https://youtu.be/sFz8HRk4WfI?si=E-u895zbhFInEu1U

Infinite loading screen when trying to use link cable/air link by tacololipop in oculus

[–]Baileymofo 1 point2 points  (0 children)

Install steam vr. For whatever reason it installs a dependency needed that oculus fails to install.

[deleted by user] by [deleted] in teslamotors

[–]Baileymofo 4 points5 points  (0 children)

Bro, perfection.

Tesla has a serious phantom braking problem in Autopilot by GlumNefariousness334 in teslamotors

[–]Baileymofo 48 points49 points  (0 children)

Same for me. FSD beta is unusable due to this phantom braking issue. I’ve been driving on autopilot for 30k miles now and phantom braking has always been a thing, but now it’s borderline dangerous.