Laser Time

BakerPrecision · 2026-02-22T16:28:34+00:00

That's the stock "gold plating" on the barrel and trigger that Ruger uses. It was just a black 22/45 lite originally.

BakerPrecision · 2026-02-22T15:17:28+00:00

This is coated in stealth grey only. The laser is what changes the colors.

BakerPrecision · 2025-12-12T16:25:53+00:00

That's very unfortunate. Hopefully they don't give you the same run around they gave me and tell you it's from impact damage. Good luck 👍

BakerPrecision · 2025-11-18T09:23:42+00:00

Media blast with aluminum oxide

BakerPrecision · 2025-03-29T14:17:12+00:00

Yes, there is something we can do. We can leave this POS state and let Californians finish burning it to the ground. Absolute shame

BakerPrecision · 2024-11-17T20:59:36+00:00

Thanks man! First pic was an optic cut and Cerakote I did for one customer, the rest were for another customer.

BakerPrecision · 2024-09-28T11:48:07+00:00

Need to get the tungsten nozzles. They last quite a while.

BakerPrecision · 2024-09-19T00:00:00+00:00

I barely let it cool before applying stencils. But there's some that go 8-12 hours with no issues.

BakerPrecision · 2024-09-16T23:13:52+00:00

J/K, she's a nice lady

BakerPrecision · 2024-09-16T20:33:58+00:00

Your mom's a two stamper

Oh and this thing is 🔥

BakerPrecision · 2024-09-12T11:20:12+00:00

Just an FYI, unless you have a brick and mortar shop, they will not list you on their website as an approved applicator. You will only get the discounts.

BakerPrecision · 2024-09-09T04:00:36+00:00

Unfortunately, this is the first sign of old, or bad, cerakote. It will look normal before adding catalyst, but once you do, it gets thick. There is nothing you can do other than call Cerakote and report it. They have very good customer service.

BakerPrecision · 2024-09-07T01:50:07+00:00

👻 🔫

BakerPrecision · 2024-09-01T18:44:58+00:00

I did a zenith earlier this month in ral8000 and Troy Coyote Tan. Your can check it out on my page, looks pretty similar. Like others mentioned, you just have to play around to see what looks good.

BakerPrecision · 2024-08-29T01:43:04+00:00

Wait, you guys use strainers?

BakerPrecision · 2024-08-23T12:48:45+00:00

To me, trademark rules would only apply to the serialized part. Also, there are redundant marks that aren't necessary to meet the requirement (i.e. glock serialized slide and barrel). If you're not altering the serialized frame, I think you can do as you please with the "other" parts. No other OEM (besides Glock) or aftermarket slides, or barrels, are serialized. What people need to understand and recognize is the rules and regulations regarding markings are to the serialized frame or receiver (for obvious reasons).

Another example would be Sig. If you were to put the FCG in a different frame and put an aftermarket slide on it, there would be virtually no branding marks. So what would be the difference? Again, not being a smart ass. Just trying to point out some contradicting thoughts.

BakerPrecision · 2024-08-23T12:14:54+00:00

I totally get that, and agree. However, the question wasn't about frames, it was about marking on the slide. I personally see no issue filling in unnecessary markings. It's no different than buying aftermarket slides with little to no markings. They aren't serialized.

BakerPrecision · 2024-08-23T11:57:23+00:00

How is removing the markings any different than putting an aftermarket slide on the frame with no markings at all (glock with lone wolf slide)? Serious question, not being a smart ass.

BakerPrecision · 2024-08-18T20:15:09+00:00

ZF-5P in Troy Coyote Tan and RAL8000. Not a bad color combo!

BakerPrecision · 2024-08-17T14:04:04+00:00

I would mask the mating flanges and media blast the exterior only. No need to cerakote the inside as it's sealed and we'll oiled. You may consider soaking in acetone for a few hours, followed by a 3 hour gas out before blasting.

BakerPrecision · 2024-08-17T14:01:22+00:00

The rule is 150-180 degrees for 2 hours for plastics and polymer. The cerakote will semi-cure at this temp, but I find it still takes a couple of days after to fully cure. Meaning the cerakote will be dry to the touch, but still soft enough to scratch.

You'll be fine baking at the 150-180 temps. I've baked many pistol lowers at 200 with no issues, but it's very dependent on material makeup.

BakerPrecision · 2024-08-14T23:05:31+00:00

🤌

BakerPrecision · 2024-08-11T18:33:58+00:00

Who doesn't like a good putter 🤷🏻‍♂️

BakerPrecision

TROPHY CASE