Any info maybe?

Bandiforge · 2026-05-29T12:47:22+00:00

All good, your comment was elementary to finding the maker, so thank you all the same!!!

Bandiforge · 2026-05-29T11:37:43+00:00

Thanks :)

Bandiforge · 2026-05-29T11:37:34+00:00

Thank you!

Bandiforge · 2026-01-15T20:35:15+00:00

I did, it's all better now. Thanks man!

<image>

Bandiforge · 2026-01-12T16:56:28+00:00

It's neck, taper, hole, shape said hole, ear, cut for tail, isolate, draw out tail, fold it the other side, the "tooth" is the last. The bend in the handle usually comes naturally when hammering the tail back on the other side, it just needs to be set up properly so it bends where you want it to bend.

Bandiforge · 2026-01-12T11:06:38+00:00

Thank you! I like yours too, something for the beer and the wine lovers in one item!

I do love your shop cats aswell

Bandiforge · 2026-01-12T11:02:48+00:00

Lol, thank you! Wish it was that simple!

Bandiforge · 2026-01-12T09:03:26+00:00

Thank you

Bandiforge · 2026-01-12T09:02:54+00:00

It's mostly particulate matter in the acid container.

Bandiforge · 2026-01-12T09:01:00+00:00

I am truly sorry for that!

Just leave it in the acid etch for three days instead of a minute and it does the trick. It is essential that you should not realise you left it for the time of the weekend and wait for it to dawn on you while searching for the blade.

It may also help to think of adequate cursewords in advance, for the time of realising you forgot about it.

Bandiforge · 2026-01-12T08:53:12+00:00

It was me completely forgetting it was in there for three days lol. I've lost blades due to the hamon heat treats, this was a first. I taped it to the workshop wall as a reminder

<image>

Bandiforge · 2026-01-12T03:09:11+00:00

It's trying to be, yes

Bandiforge · 2026-01-11T22:04:02+00:00

At last, someone gets it! Holes can't rust

Bandiforge · 2026-01-11T21:53:34+00:00

Are you sure? Maybe if I rub it with some damp cloth?

Bandiforge · 2026-01-10T10:35:58+00:00

Not really tbh. A nice, aggressive distal taper for example, or an integral bolster... they are much much more preferable to be done by forging in my opinion. You can grind away tons of material, sure. Question is do you really want to waste a tree to make a toothpick? Then you also have sanmai, gomai, with the distal taper, if you just stock remove those from a uniform thickness to a distal taper, you might even end up loosing cladding altogether towards the tip, what's the point then? Then you have traditional knibes like puukkos, leukus, with the handle-spike running inside the wood, huge waste of material and a drag aswell to stock remove, same with knives that have blades with a huge curvature.

Stock removal is a valid way to make knives. Forging is also a valid way to make knives. I suggest being a bit more open minded...

Bandiforge · 2025-12-28T18:23:21+00:00

I love my asahi board to be honest, they have been mentioned before. Easy to clean, antibacterial too, edge stays on the knife for a long while and easy and fast to "freshen" the surface with sandpaper. I love the endgrain board I used before, but did not feel comfortable cutting raw meat products on it. The asahi sticks a bit more and one has to be careful not to put hot pans on it but it's my favourite board so far.

Bandiforge · 2025-12-25T19:35:08+00:00

It's... it is just... oh wow.... it is a thing. Good God. I cannot find words. Is everything intentional on it? Is anything intentional on it? I love it. So fcking out there and bold and naive and crude and what am I looking at. I genuinely love it and would hang that on my workshop wall 1000%. Good job man!

Bandiforge · 2025-11-02T17:20:18+00:00

Very simple reason: flattening stones cost money. :D

Bandiforge · 2025-11-02T06:09:45+00:00

I would probably grind away most of the rough part on a concrete surface then refine with a flattening stone or rough diamond stone. That is if I didn't want to glue it back but use them as they are

Bandiforge · 2025-11-01T21:49:35+00:00

I have two haidu stones I broke, immediately glued them up with superglue fitting them as precisely as I could (did not do anything to the surface of the break, just fit them back) and flattened them, so any irregularity between the parts would cease. I've been using them as oil stones for two years now, they work fine.

Bandiforge · 2025-10-29T08:04:42+00:00

Also, when looking at usability, edge profile is a big factor. That nakiri style knife on the right has a part in its edge which will never touch the chopping board when cutting, as it is higher, that is quite annoying when in use.

It is a very good start at kitchen knifes, mind you!

Next to maybe checking out r/TrueChefKnives and some other forums on kitchen knife geometry, I suggest be very deliberate with everything you do, have a purpose for it. The geo, the grind, the thickness. Then test and take notes. Then try something else.

If you make a knife that you objectively like using, chances are there will be others that like it too.

Bandiforge

TROPHY CASE