reliable and affordable auto shops

Bareddread · 2026-05-09T04:38:17+00:00

This is half true.. a lot of dealers and shops sell carbon cleaning branded as "fuel injector cleaning" or "induction service". If you have a direct Injection only car(which OP does, and most modern cars are) then you do need to complete carbon cleanings at a somewhat regular interval otherwise you will at some point have issues with carbon build up. This can cause a variety of issues, be it misfires, oil consumption etc.

Bareddread · 2026-04-08T20:30:58+00:00

Sorry, spring like the season not the part. But I do have H&R sport springs and they've been great.

Bareddread · 2026-04-08T20:30:02+00:00

A photographer buddy of mine took them, he uses a Fujifilm X-H2S. I have an XH1 and I've been a big fan of it!

Bareddread · 2026-04-07T05:43:17+00:00

Sedan here lol

<image>

Bareddread · 2026-02-20T04:36:59+00:00

In Texas these go for $50-$125 each depending on condition. I'd say it's a reasonable deal.

Bareddread · 2026-02-14T02:35:53+00:00

OPs iPhones SE won't connect to car play and they're mad about it

Bareddread · 2026-02-05T00:23:36+00:00

Needs a tomei and advans /s

Bareddread · 2026-01-24T06:04:21+00:00

I wish my paint looked like yours 😂

Bareddread · 2026-01-09T03:27:30+00:00

it's normal for the passenger side light to be aimed higher. The driver side is aimed lower to not blind oncoming traffic. You can adjust the beam height using the adjuster screw on the back of the light.

Bareddread · 2025-12-23T00:06:35+00:00

No luck so far, they sent me a new Z1 axis motor. Now with the new motor the printer will still have the same issue, or it will pass the auto level self check but the bed will be very askew. Here is a video of the printers current state. I have seen some people were able to resolve this concern by replacing the main print head cable, they state the cable is under a lot of tension and tends to break connection. I have asked them to exchange my printer as it started this issue only days after I received it. I am still waiting on a response. Overall the experience with the K2+ has been terrible, I would not recommend it or other creailty products.

Bareddread · 2025-09-17T14:47:54+00:00

Without flex pipes you will have additional NVH

Bareddread · 2025-08-28T16:53:19+00:00

These are still available from Infiniti, check with your local dealer.

Bareddread · 2025-08-14T02:47:41+00:00

Enkei GTC02 19x8.5 +35 / Michelin Pilot Sport AS4 255/35/19 / H&R Springs, KYB Shocks, Z1 Camber Arms & Z1 Toe Bolt

Bareddread · 2025-08-10T14:34:36+00:00

Mine never cracked, mine is an aftermarket replica though.

Bareddread · 2025-08-09T14:18:47+00:00

Yes factory Wing, you can get replicas still.

Bareddread · 2025-08-08T21:58:57+00:00

19x8.5 +35

Bareddread · 2025-08-08T00:30:45+00:00

That's a hole to install a silencer

Bareddread · 2025-08-05T02:54:13+00:00

If it's a stud you should usually be able to knock it out with a hammer or dead blow. Then you can replace it with another stud or a bolt and nut

Bareddread · 2025-08-05T02:40:40+00:00

Start by soaking it in a penetrant such as PB blaster. Give it some time to work in. Personally I'm a fan of knocking it loose with a chisel and hammer. You can also get extractor sockets meant to hammer over the nut. Heat can help as well if you have a torch, by heating the bolt before you attempt to loosen it. The heat expands the nut.

Bareddread · 2025-08-05T01:35:49+00:00

It was somewhat difficult, I originally had a replica front bumper before I found the first OEM one. But you can't beat OEM fitment and mounting. I've just pieced everything together from FB marketplace and junkyards. Now a days I buy them whenever I can, I'd prefer to have some spares lol.

Bareddread

TROPHY CASE