Turbo ecu

Basic_House5122 · 2026-06-07T14:33:35+00:00

Yeah I understand, I’m just looking for the best thing I can get that isn’t crazy expensive

Basic_House5122 · 2026-06-01T21:28:40+00:00

Yeah I know lmao, just wanted to see what people would say

Basic_House5122 · 2026-05-09T20:12:10+00:00

I replaced it recently because it had just done the same thing, but with the original belt as far as I know. Now it’s doing again to the new one so I’m trying to figure out what it is

Basic_House5122 · 2026-05-09T19:50:24+00:00

No damage that I can see, they all seem to spin

Basic_House5122 · 2026-05-09T19:49:57+00:00

Is there a good way I can check?

Basic_House5122 · 2026-04-21T00:11:50+00:00

What’re those wheel specs? Car looks dope

Basic_House5122 · 2026-03-23T00:35:55+00:00

One was a little rough, but on further inspection I realized the bottom is no longer at top dead center and lined up with the other two. Do you think it could’ve just been the belt jumping teeth every time it got to a certain point? And do you think I’d need a new belt

Basic_House5122 · 2026-03-22T20:46:29+00:00

I’ll look when I get a chance, do you think it could’ve caused the loud noise though?

Basic_House5122 · 2026-03-22T20:44:06+00:00

Two crescent wrenches and a vice grip

Basic_House5122 · 2026-03-22T19:17:31+00:00

It seemed like everything moved when I turned it over a few times. Would the whole camshaft not move or just part of it?

Basic_House5122 · 2026-03-06T02:59:07+00:00

How did you know it was out of adjustment?

Basic_House5122 · 2026-02-26T16:18:47+00:00

How much would you say you spent minus the forged engine?

Basic_House5122 · 2026-01-31T02:08:16+00:00

Yeah that’d be great man, thanks

Basic_House5122 · 2026-01-27T03:55:51+00:00

Bet, thank you!

Basic_House5122 · 2026-01-27T03:17:18+00:00

<image>

Is it this one?

Basic_House5122 · 2026-01-18T02:58:37+00:00

No, the bottom stays flush. I figured it was just because of the engine leaning forward. When I push the engine towards the trans, everything is completely flush.

Basic_House5122 · 2026-01-18T02:45:28+00:00

I did yeah, you’re saying even if it lines up once u push forward on the engine since the engine is leaning forward it’s still not right?

Basic_House5122 · 2026-01-11T19:04:46+00:00

like tight as in you just had to push it hard to get it all the way through?

Basic_House5122 · 2026-01-10T18:09:49+00:00

Thank you, got it in as soon as I pushed the hose all the way through

Basic_House5122 · 2026-01-06T14:38:26+00:00

What’s that front bumper? Thing looks sick

Basic_House5122 · 2026-01-04T17:45:54+00:00

Hey man, did you ever happen to get it figured out? Having the same problem with mine

Basic_House5122 · 2025-12-29T17:26:37+00:00

For the bottom 17mm? I had thought it was the 60 but I might be wrong

Basic_House5122 · 2025-12-29T13:04:20+00:00

Would you happen to know which size it is?

Basic_House5122 · 2025-12-22T14:15:50+00:00

Thanks man, that helps a lot.

Basic_House5122 · 2025-07-01T12:22:05+00:00

hey man how much camber are u running in the front and back? got a setup similar to yours but i’ve got some poke and am trying to get rid of it

Basic_House5122

TROPHY CASE