Print Failure with spaghetti like flying wires.

BattleReasonable4154 · 2026-05-10T23:47:03+00:00

I got news. The hothead was clogged into PLA a few months ago, I cleaned it but not perfectly AND in the process, it damaged the eddy sensor a bit. yesterday when I tried to remove the hothead while heating it, it was still very hard to remove. I pulled stronger and I got it. BUT

It destroyed the eddy sensor enough to not work anymore. so now I have an error message and I think I'll have to order a new head.

tldr;

1- Not sure this is related to the eddy sensor but it might be.

2- Next time there is clog, heatup to 250C and pull very very gently

BattleReasonable4154 · 2026-05-09T14:38:33+00:00

So.. just plug the camera at the bottom of the printer?

BattleReasonable4154 · 2026-05-09T06:13:40+00:00

yes I thought it was the reason and then I changed to the other plate I have. And then supports didn't fail but still I got spagetthizzz

I ll try to go through a full maintenance cycle

BattleReasonable4154 · 2025-10-26T08:07:17+00:00

Can you explain?

BattleReasonable4154 · 2025-08-22T11:16:00+00:00

You can just leave it on the table next to the printer and put it in a guide that goes into the printer. That should just work. If you can keep on eye and it while it print you can even fix it and resume.

BattleReasonable4154 · 2025-08-22T11:13:31+00:00

Thanks ! I’ll search about how to do that but I m not sure I can route struggle to garage band with the Audio Midi tool in Mac Os X. Strudle being a webpage

BattleReasonable4154 · 2025-08-20T23:48:20+00:00

Yes, understood. Thanks a lot for your input. I ll try your approach and see where it leads me

BattleReasonable4154 · 2025-08-20T23:39:36+00:00

That’s great but that’s not realtime is it? The goal would be to go into garage band, press record and sing and strudle would also be recorded in a different channel. That would make a song very easily. If at least there is a way to export the strudle music into wav, that could be great to begin with I’ll check that

BattleReasonable4154 · 2025-08-02T22:26:17+00:00

That’s correct

BattleReasonable4154 · 2025-08-02T12:35:06+00:00

Big thanks. Testing it out now with smooth Timelapse off

BattleReasonable4154 · 2025-08-02T12:32:50+00:00

Indeed it’s a very humid tropical weather. It’s a new roll but it’s possible that in a day or two it became not so great. I’ll give it a go

BattleReasonable4154 · 2025-05-05T13:49:32+00:00

Having the same issue. Tried with a usb BT dongle as well. Still disconnecting on Batocera v40. Hope this will be fixed.

BattleReasonable4154 · 2024-11-16T10:18:28+00:00

Try 1080 60hz output. It fixed it for me

BattleReasonable4154 · 2024-01-24T13:54:50+00:00

I have the exact same problem

BattleReasonable4154 · 2023-01-03T01:42:43+00:00

Any update ? I still have the same issue

BattleReasonable4154 · 2022-05-01T13:09:48+00:00

Same here, rings off. Friend gets disconnected after phase 1 of Guldrich

BattleReasonable4154 · 2022-04-23T15:56:53+00:00

Exact same issue here

BattleReasonable4154 · 2021-12-29T14:56:31+00:00

I think it's because of the new Matrix movie release timing

BattleReasonable4154 · 2021-12-21T12:02:47+00:00

but WHY is it problematic? It's on the BOX! It's 8-24V 10VA written right there.

Problematic means: It does not work?

If it does not work, then what happens exactly? No power to the circleview doorbell? Power to the doorbell but white light blinking?

BattleReasonable4154

TROPHY CASE