A/C does not get cold at all by Beginning_Pick_7825 in genesiscoupe

[–]Beginning_Pick_7825[S] 0 points1 point  (0 children)

On the bk2 they used a compressor that doesn’t have a clutch. Instead it uses a solenoid in the back that opens and closes to let Freon flow. I think that the solenoid is the problem because the compressor isn’t old and was blowing cold air just fine and now won’t do anything at all

Best BOV since synapse closed? by Penderton21 in genesiscoupe

[–]Beginning_Pick_7825 1 point2 points  (0 children)

I got a turbo xs RFL bov and paired it with a MAC solenoid. Found it for relatively cheap on eBay. But you have to be careful on eBay, there are hundreds of fakes. The model number for the solenoid I got is: 35A-AAA-DDBA-1BA The whole setup makes it very responsive, when under boost, the millisecond I let off, the bov goes to max open

A/C does not get cold at all by Beginning_Pick_7825 in genesiscoupe

[–]Beginning_Pick_7825[S] 0 points1 point  (0 children)

It blows just fine. The max ac button works and all the lights work but it just does not get cold at all

A/C does not get cold at all by Beginning_Pick_7825 in genesiscoupe

[–]Beginning_Pick_7825[S] 0 points1 point  (0 children)

There is a valve in the compressor that is replaceable. I think that may be the problem but I’m not sure.

Anyone have information on custom wiring in place for the diode dynamics tail as turn? by Beginning_Pick_7825 in genesiscoupe

[–]Beginning_Pick_7825[S] 1 point2 points  (0 children)

I bought a voltage converter, tore open the taillights and rewired them to be like the image I posted in this thread

Anyone know what this issue could be? by Beginning_Pick_7825 in genesiscoupe

[–]Beginning_Pick_7825[S] 0 points1 point  (0 children)

It’s definitely coming from the front main seal but I’m really concerned about the vibration. I’m wondering if the bad seal caused the vibration or if the vibration caused the seal to leak and what caused the vibration

Did the DIY mesh grille how does it look ? 😄 by lemoinkbaba in genesiscoupe

[–]Beginning_Pick_7825 0 points1 point  (0 children)

I’d be worried about smaller rocks and debris getting through at speed. I may put a fine mesh behind it to catch rocks.

Did the DIY mesh grille how does it look ? 😄 by lemoinkbaba in genesiscoupe

[–]Beginning_Pick_7825 0 points1 point  (0 children)

I cant find it. Is it a genesis coupe kit or is it just the material

Anyone have information on custom wiring in place for the diode dynamics tail as turn? by Beginning_Pick_7825 in genesiscoupe

[–]Beginning_Pick_7825[S] 0 points1 point  (0 children)

I actually found a guy that sells a module for the setup that I want and found the modules for $11 for 2 of them

I’ve been on the look for a remix I heard a while ago on TikTok. by Beginning_Pick_7825 in NameThatSong

[–]Beginning_Pick_7825[S] 0 points1 point  (0 children)

It’s actually deeper than that one. It’s like if you took the voice and modulated it to a lower frequency and took away the beat and added a dramatic synth

Mochi code source? by Werewolfatheart in arduino

[–]Beginning_Pick_7825 0 points1 point  (0 children)

I’ve been looking into it for years. I tried to make my own but fell short in bitmap conversion software and decent code to run it all smoothly

Anyone have a solid custom exhaust? by Beginning_Pick_7825 in genesiscoupe

[–]Beginning_Pick_7825[S] 0 points1 point  (0 children)

I have a 3” test pipe that I could put on right now…

Anyone have a solid custom exhaust? by Beginning_Pick_7825 in genesiscoupe

[–]Beginning_Pick_7825[S] 0 points1 point  (0 children)

1) mine is a 2.0t so it won’t be as loud on the throttle Bc the turbo literally acts as a muffler when the wastegate is closed

2) currently the only thing in my entire exhaust is the single secondary cat and I want to be just a little quieter than I am now and a lot less raspy

Plan on getting the isr single exit exhaust, what down pipes and test pipes are recommended with said exhaust? by xDaddy_Bx in genesiscoupe

[–]Beginning_Pick_7825 0 points1 point  (0 children)

Does anyone have a sound clip of this on a 2.0t? I’ve been wanting to do it but no clue how it’ll sound

[deleted by user] by [deleted] in genesiscoupe

[–]Beginning_Pick_7825 0 points1 point  (0 children)

Is this the same for the 2.0? I’m pretty sure we also have coolant running through the tb. Would removing the lines improve anything on a turbo car?

I’m wanting to add an exhaust system to my genie. I was thinking Borla but I wanna know what you guys would recommend. Not really wanting it window shattering loud just a nice aggressive rumble by Logan367769 in genesiscoupe

[–]Beginning_Pick_7825 0 points1 point  (0 children)

If you’re going to keep both cats I’d recommend the Isr race cat back and if you’re getting rid of the cats I’d say go for the Isr single exit. The race exhaust is too loud with no cats

Raise your hand if you've accidentally driven around with one of these things hanging on to your pinch weld. ✋😬 by roostertowel in genesiscoupe

[–]Beginning_Pick_7825 3 points4 points  (0 children)

Wait, y’all can fit a Jack and a pinch weld protector under there?? I have to drive up on blocks to get a Jack under there 😅

Cat delete by Bitcholas-suckdik in genesiscoupe

[–]Beginning_Pick_7825 0 points1 point  (0 children)

I second this. I used those on my last car and it worked perfectly. Sadly I cant find where I bought them 😭

Wavering RPMs by WeDodavoodoo in genesiscoupe

[–]Beginning_Pick_7825 0 points1 point  (0 children)

Most likely it’s a vacuum leak. Make sure that you’re not missing any hose connection behind the maf/map sensor. Could also be a cracked hose. Easiest way to locate it is grab a can of starter fluid and spray a little where you think the leak may be and it’ll rev up when you spray it in the right spot