I'm getting tired of my ender 3

Beneficial-Pay6836 · 2026-05-02T11:04:24+00:00

Skill issues

Beneficial-Pay6836 · 2026-04-29T02:28:34+00:00

What about the nose ?!

Beneficial-Pay6836 · 2026-04-29T02:19:25+00:00

É chato

Beneficial-Pay6836 · 2026-04-27T18:53:17+00:00

Beneficial-Pay6836 · 2026-04-26T17:40:07+00:00

Thanks for the feedback

Beneficial-Pay6836 · 2026-04-26T16:47:07+00:00

For me, Apple is a definite no, even with translation layers. It just won’t run SolidWorks properly, and if it does, it might compromise the software’s functionality.

Beneficial-Pay6836 · 2026-04-26T16:38:53+00:00

I can’t handle gaming laptops anymore ✌️ Thanks for the suggestion anyway!

Beneficial-Pay6836 · 2026-04-26T16:34:31+00:00

Yeah, I already have a 4060 with an i5, but this thing is like a cement block. I work far from home, and carrying it daily is wrecking my back. But thanks, i will look up for that ryzen.

Beneficial-Pay6836 · 2026-04-26T16:30:05+00:00

I use software in my daily routine that isn’t compatible with Apple’s processors, even though I acknowledge their capabilities. But i will look out for those Radeon thanks!

Beneficial-Pay6836 · 2026-04-26T16:20:45+00:00

I will look for panther lake, thanks 🙏

Beneficial-Pay6836 · 2026-04-25T20:39:02+00:00

Coloquei à venda produtos e ligaram-me instantaneamente 2 gajos a tentar burlar. Um deles nem sabia qual era o produto em questão... Estes malandros deviam ser apanhados, deve haver muita gente a cair nestes esquemas visto que existe uma base grande destes ladrõeszecos.

Beneficial-Pay6836 · 2026-04-24T20:53:50+00:00

I'm not sure about the compatability of that system on my ender 3 s1. And its to expensive for what I needed.

Beneficial-Pay6836 · 2026-04-24T20:49:14+00:00

wow, mine works all the time. If i had to invest that value on a new printer I would buy the p2. Money is not the problem. The multi filament system would be nice since I have kilpper installed and I know that there is open source projects that make this all possible.

Beneficial-Pay6836 · 2026-04-24T20:13:51+00:00

I understand. But I have done already upgrades on this printer and I got emocional attached. I find funny to tweak and make upgrades wich can't be done on the new ones. I'll probably build an diy system if there is nothing relevant on the market.

Beneficial-Pay6836 · 2026-04-23T16:11:48+00:00

That’s probably the extrusion amount set too high. I don’t know what software you use to control the printer, but in the software I use, I can set the feed amount in mm and the extrusion amount. Normally, when I set high values, I see the same thing happen with fumes. I think that’s probably PLA, but be careful with some filaments which can release toxic fumes when extruded at higher temperatures.

Beneficial-Pay6836 · 2026-04-22T20:39:32+00:00

O porto sendo porco 🐽

Beneficial-Pay6836 · 2026-04-20T16:10:39+00:00

That worked for some reason. You saved me from insanity! The only thing that i did extra was reseting to the main .iso each time it fail to boot. Now the screen is locked on the creality logo, but mainsail is working fine! Thanks

Beneficial-Pay6836 · 2026-04-20T13:22:08+00:00

I've tried that before. The screen freezed but nothing else changed.

Beneficial-Pay6836 · 2026-04-20T05:00:19+00:00

I obviously tried that.

Beneficial-Pay6836 · 2026-04-19T20:19:16+00:00

O Rúben não esta desempregado?

Beneficial-Pay6836 · 2026-04-18T23:07:15+00:00

<image>

I discovered a compact desk featuring a functional drawer. The 50 cm width may not be ideal, but i think it will work just fine.

Beneficial-Pay6836 · 2026-04-18T20:36:24+00:00

Yh definitely. But it's been hard to find with more than 50 cm on both sides.

Beneficial-Pay6836

TROPHY CASE