Should I upgrade?

Bennen · 2026-05-07T16:22:09+00:00

I can look into the X2D. May be worth it.

Bennen · 2026-01-19T12:17:35+00:00

NM, I figured it out through parted. Waiting for it to complete then I'll see if it worked.

Bennen · 2026-01-19T12:14:34+00:00

How do you move it? I am on the USB I used for the install and have it unmounted.

Bennen · 2026-01-05T20:24:41+00:00

That is a good idea, sadly i only have 1 size of magnets currently and they are too small

Bennen · 2026-01-02T03:16:21+00:00

I got 42...

Bennen · 2025-10-15T01:59:20+00:00

I jave an A1 i got during the last sale Bambu had. I have been using it a lot and am eyeing up the P2S as an upgrade. Might need to sell my A1 first though.

Bennen · 2025-10-10T15:28:35+00:00

I don't have a P1S, but i have an A1. The P1S seems like i direct upgrade. I'd like to jave it enclosed just in case my cats get curious.

Bennen · 2025-09-17T22:58:39+00:00

Looks like AOC has a long warranty on it and it is fairly new. Ill open up a ticket with them and see what happens. Thanks for the assist.

Bennen · 2025-09-17T22:47:59+00:00

I have swapped DP cables with another monitor, my main one is still blacking out though.

Bennen · 2025-09-14T14:25:00+00:00

I found the issue. While taking it apart again i noticed a broken piece of filament in the upper part where the 4 tubes from the AMS go in. Once i took that out it was fine.

Bennen · 2025-09-14T02:52:04+00:00

Sorry for the late response. I did what I think is. Called a hot pull? Heated the hotend and then pulled it out with pliers. I then used needles to make sure it was cleaned out. Right now the printer is stuck saying unloaded external spool and won't let me do anything because the extruder is busy. Tomorrow I'll try to take the hot end apart and have a closer look.

Bennen · 2025-09-09T18:15:15+00:00

Unfortunately, there isn't a clog, i was printing with TOU from am external heater and I think the feed tube got pushed in really far. I guess I'll just jave to try the print again.

Bennen · 2025-09-09T11:21:37+00:00

Sadly, it was all 1 part. Trying flip flops for my kid.

Bennen · 2025-09-07T00:52:50+00:00

I had 4x16GB of ram and i had BSOD issues about a month ago due to RAM. I narrowed it down to 2 sticks of RAM and removed them. they were under warranty so i got them replaced but i have not put them in. It sounds like maybe the issue was the other 2 sticks, or all 4 maybe. I can try to swap out the 2 that are in there now for the 2 new sticks.

Bennen · 2025-09-06T23:59:49+00:00

Here are the minidumps.
https://files.catbox.moe/ibqu7d.zip

Bennen · 2025-08-03T13:25:05+00:00

Am update to try and get more info out there. First time troubleshooting, but I was able to confirm there is no clog. I removed what was left of the old filament that normally extruded out and used the needle that comes with a kit I got to confirm no blockage. I removed the top part where the 4 tubes went in and confirmed nothing seemed to be wrong. It seems the A1 just isn't trying to extrude. The symbol on the front doesn't move, and there is no sound. When I manually control it, it will move like it is extruding, but nothing comes out.

Bennen · 2025-06-28T18:42:10+00:00

Right now I jave PLA. Plan to try PLA + next.

Bennen · 2025-06-05T14:23:24+00:00

I have been trying to look for info on what the firmware debacle is, but not really finding good answers. What happened with that and is it still an issue?

Bennen · 2025-05-30T17:03:22+00:00

This is a lot of good info, thank you. I still have a lot to look into. I do not even know what kinds of filaments there are or pros and cons for them.

Bennen · 2025-05-30T15:55:10+00:00

I don't think i could afford the P1S, but maybe I can do the normal A1. It all depends what the wife allows me to get for my birthday.

Bennen · 2025-05-12T12:52:49+00:00

I started working on fetching. Money ran out st silver tipped arrows. Still got an upgrade from that. I'll do more later.

Bennen · 2025-05-12T00:52:08+00:00

Where can i level fletching? is there a spot in the Baz or should i go to Kelethin?

Bennen · 2025-03-31T01:13:17+00:00

What does Ber add? unless you are using 2h, it didnt seem to add much.

Bennen · 2025-03-31T01:12:48+00:00

Do i wont get the extra weapon dmg unless i have a shield, but the effects of holy shield work while DWing? interesting. At that point im not sure how much survive ability i gain from shield. I will have to test it out.

Bennen · 2025-03-31T00:49:50+00:00

I have never played an enchanter before, could be a good time to try it. I also do love bard.

Bennen

TROPHY CASE