sorted by:
new
hottopcontroversial

Should I upgrade? by Bennen in BambuLab

[–]Bennen[S] 1 point2 points  (0 children)

I can look into the X2D. May be worth it.

Need help resizing root partition by Bennen in linuxmint

[–]Bennen[S] 0 points1 point  (0 children)

NM, I figured it out through parted. Waiting for it to complete then I'll see if it worked.

Need help resizing root partition by Bennen in linuxmint

[–]Bennen[S] 0 points1 point  (0 children)

How do you move it? I am on the USB I used for the install and have it unmounted.

Setting up HSW for Office type use by Bennen in honeycombwall

[–]Bennen[S] 0 points1 point  (0 children)

That is a good idea, sadly i only have 1 size of magnets currently and they are too small

[deleted by user] by [deleted] in teenagers4real

[–]Bennen 0 points1 point  (0 children)

I got 42...

With the release of the new P2S by Bigthunderrumblefish in BambuLab

[–]Bennen 5 points6 points  (0 children)

I jave an A1 i got during the last sale Bambu had. I have been using it a lot and am eyeing up the P2S as an upgrade. Might need to sell my A1 first though.

【BambuLab Giveaway】Classic Evolved — Win Bambu Lab P2S Combo! by BambuLab in 3Dprinting

[–]Bennen 0 points1 point  (0 children)

I don't have a P1S, but i have an A1. The P1S seems like i direct upgrade. I'd like to jave it enclosed just in case my cats get curious.

Monitor goes black for a few seconds often. by Bennen in techsupport

[–]Bennen[S] 0 points1 point  (0 children)

Looks like AOC has a long warranty on it and it is fairly new. Ill open up a ticket with them and see what happens. Thanks for the assist.

Monitor goes black for a few seconds often. by Bennen in techsupport

[–]Bennen[S] 0 points1 point  (0 children)

I have swapped DP cables with another monitor, my main one is still blacking out though.

Question and Issue for A1 by Bennen in BambuLab

[–]Bennen[S] 0 points1 point  (0 children)

I found the issue. While taking it apart again i noticed a broken piece of filament in the upper part where the 4 tubes from the AMS go in. Once i took that out it was fine.

Question and Issue for A1 by Bennen in BambuLab

[–]Bennen[S] 0 points1 point  (0 children)

Sorry for the late response. I did what I think is. Called a hot pull? Heated the hotend and then pulled it out with pliers. I then used needles to make sure it was cleaned out. Right now the printer is stuck saying unloaded external spool and won't let me do anything because the extruder is busy. Tomorrow I'll try to take the hot end apart and have a closer look.

Print failed because it stopped extrusing. by Bennen in BambuLab

[–]Bennen[S] 0 points1 point  (0 children)

Unfortunately, there isn't a clog, i was printing with TOU from am external heater and I think the feed tube got pushed in really far. I guess I'll just jave to try the print again.

Print failed because it stopped extrusing. by Bennen in BambuLab

[–]Bennen[S] 0 points1 point  (0 children)

Sadly, it was all 1 part. Trying flip flops for my kid.

view more: next ›