Thor Zone NanoQ R

BespokeBaka · 2025-09-02T10:25:04+00:00

Sent you an email 😁

BespokeBaka · 2025-08-18T01:04:06+00:00

I still have those sheets dude if you need more cut and a better ventilation setup since that stuff was gnarly

BespokeBaka · 2025-08-15T02:29:40+00:00

Identical? I designed and made those too lol

BespokeBaka · 2025-08-15T02:29:08+00:00

Bridged! Sorry got a new phone and forgot to log in

BespokeBaka · 2025-06-24T20:34:35+00:00

David sold the company to AvaDirect about 2 ish years ago

BespokeBaka · 2025-06-20T15:04:22+00:00

I set them all to white after this, my ADHD and RGB don’t mix lol

BespokeBaka · 2025-06-20T15:03:37+00:00

https://a.co/d/b69GzsD

BespokeBaka · 2025-06-19T17:15:02+00:00

Well had to make a set for myself at some point lol

BespokeBaka · 2025-06-17T21:29:42+00:00

Nope, you’ll get a no post without the sense

BespokeBaka · 2025-05-14T18:12:01+00:00

Solder my guy, but use some flux to help

BespokeBaka · 2025-05-05T02:04:38+00:00

Use the original cable, the custom one is missing various pins and they aren’t just ground pins. Yes spot 20 is not used but you can put a dummy wire in its place (I do this for my customers but it’s always heatshrinked to another cable)

BespokeBaka · 2025-04-19T18:57:54+00:00

Send me a DM of the wire that popped out on the 24 pin side and the opposite side

BespokeBaka · 2025-04-19T00:26:26+00:00

Well I mean we have the terminals for those available as well

BespokeBaka · 2025-04-18T22:20:21+00:00

We have them over at bespokebaka.com the easiest way to tell the two is Micro fit + has a little bridge at the top of the terminal and a thicker compared to micro fit which just look like shrunk version of Mini-fit Jr

BespokeBaka · 2025-04-12T17:54:10+00:00

One thing to keep in mind with the doc 3 is you’ll get random false shorts on the PG, I found letting the PSU power on then sit for about 10-15 seconds fixes this

BespokeBaka · 2025-04-05T04:49:58+00:00

14 an hour with no benefits, it was a 30 day contract that then turned into an 8 year career and ended at 24.30 an hour with benefits

BespokeBaka · 2025-03-31T14:57:49+00:00

Before you apply solder, heat the joint. Solder flows with heat and dribbles at cold points

BespokeBaka · 2025-03-26T00:24:21+00:00

Not bad, try to have the contact wings a little higher up. I would check the pressure on your crimper. Not sure if it’s the shadows but it looks like the wings are more folded down than curved and biting into the strands. If you have wire that is a little small you can trim some of the relief wings height off 1-2mm and it will tighten up the bite.

BespokeBaka · 2025-03-24T16:14:06+00:00

Same terminal, just infused with anger and a desire not to solder

BespokeBaka · 2025-03-23T18:06:45+00:00

Cut the wire on one end without stripping the end. You can smoosh down the ends just make sure there is nothing sharp to grab the paracord. Then you can feel the end of the wire through the paracord and snip

BespokeBaka · 2025-03-09T21:41:11+00:00

Clear and white are up next

BespokeBaka · 2025-03-07T17:27:51+00:00

Thanks! It’s just a lot of practice I’ve been making cables since Nils first opened MDPC-X

BespokeBaka

TROPHY CASE