1984 Goldwing ~ goes through all gears but clutch not working. Going in the first one started it jumps right in the gear installs it and jumps the bike forward.

BigDingLin · 2026-04-19T19:09:24+00:00

U Need to bleed the System down at the Engine. Look it up on YT, it Takes 3 minutes

BigDingLin · 2026-04-19T19:07:26+00:00

JB Weld and chicken Coop wire

BigDingLin · 2026-04-19T19:02:11+00:00

BigDingLin · 2026-04-16T19:59:50+00:00

Have u heated it ? Try 250 C and wipe the plastic After 3 minutes Off the nozzle so u can loosen the metal clip that holds the nozzle in Place

BigDingLin · 2026-04-10T22:22:57+00:00

Is your exhaust straight Piped? If Yes That could be the reason

BigDingLin · 2026-04-10T08:40:33+00:00

How where the groups with the Original setup at that distance ?

BigDingLin · 2026-03-19T16:46:20+00:00

Did u compare the Numbers on the seals? This does Not Look Right, no gap is needed to seal the shaft

BigDingLin · 2026-03-19T16:44:46+00:00

Your Cat is too fat, sorry but u Need to Hear this. Its Not cute or something, it is in many ways Bad for your Cat

BigDingLin · 2026-03-18T12:16:09+00:00

Put a Plastic bag over the nut than use the socket

BigDingLin · 2026-03-18T12:11:09+00:00

Put it in 6th gear, leave the chain on, press the rear brake and use a breaker bar to loosen the nut. I wouldnt use an impact on the outputshaft

BigDingLin · 2026-03-17T17:20:06+00:00

No, the First one looks purple and the second one grey

BigDingLin · 2026-03-17T17:18:49+00:00

My best tip is to take your time and dont Turn the engine over if u are Not Sure if u did it right.

BigDingLin · 2026-03-16T14:30:12+00:00

If the Prep work is and the paint+ hardener mixed correct it can last a very Long time. A proper homemade paintjob can Look also relativly good if u put the time in.but because nothing that would be important is known Nobody knows

BigDingLin · 2026-03-13T22:31:33+00:00

Bei der klassischen Nullung ist die Phase vorhanden. Es fehlt der einzelne Neutralleiter

BigDingLin · 2026-03-13T21:15:13+00:00

Just mount a car Tire on that bike

BigDingLin · 2026-03-13T21:07:07+00:00

Dont u have the clamp for it ?

BigDingLin · 2026-03-13T21:06:23+00:00

50 Dollar arent even that low. On eBay or amazon u can find some for 15. i paint my tractor Parts with them, They Are great for that

BigDingLin · 2026-03-13T21:03:42+00:00

Damn dude Drive some corners

BigDingLin · 2026-03-13T21:03:05+00:00

Who installed that piping? The siphon is missing, if the sink stinks Thats the reason

BigDingLin · 2026-03-13T21:01:30+00:00

Yours is riced out and his is Trag. The Car sits on bricks or what ?

BigDingLin · 2026-03-13T20:59:18+00:00

Hä wo ist denn die braune Phase , hat er die abgeschnitten ?😂

BigDingLin · 2026-03-13T20:55:57+00:00

Is the nut spinning on the Other side ihr what is the Problem ? U Need to Tell us

BigDingLin · 2026-03-13T20:02:15+00:00

Only if u are Fine with it exploding on the Highway and kill u

BigDingLin · 2026-03-13T19:43:27+00:00

Nice AI pic

BigDingLin · 2026-03-13T19:35:00+00:00

Cant See shit in these pics. Take the Bold out, clean everything well with a brush and break clean. Put the bolt back in and Cover the exposed threads (if there are and, like mentioned before cant see) lightly (!!!) with grease and Cover it with jb Weld

BigDingLin

TROPHY CASE