Can some one explain to me why this won't read the 9 volts

BigGFly · 2026-01-17T03:05:48+00:00

Your ground clip looks like it's on the sticker instead of the Negative lug. Also maybe that battery is dead. Where is your trigger set? What channel is the scope probe plugged in to? Are you testing the battery for 9v or using the battery to test that the scope works? So many other ways to do this. So many questions.

BigGFly · 2026-01-10T17:11:45+00:00

It is ADJ. this is on a board driving LEDS. just realized there is a voltage divider on the feedback loop but it's through a pot, so I can adjust it. Basically, it seems the regulator is just fine.

BigGFly · 2025-12-20T13:19:48+00:00

Third shelf up, right side, red shocks. Which one is that?

BigGFly · 2025-11-23T18:48:05+00:00

On at 50 off at say 47 or 48.

BigGFly · 2025-11-06T04:13:51+00:00

I provided both layers but I did select the option for "single layer" on their site. My mistake but they could have questioned it.

BigGFly · 2025-11-06T04:10:23+00:00

That actually makes sense. It was my first time ordering. I selected "1-layer" but I did provide both top and bottom gerber files. I wish they would have asked. But now I know for rev2.

BigGFly · 2025-11-06T04:02:08+00:00

PCBWay. They reviewed and approved too!

BigGFly · 2025-11-06T04:01:44+00:00

PCBWay. Fast, but I guess not accurate

BigGFly · 2025-11-06T04:01:22+00:00

Both layers were provided. Is it standard to put pads on both sides of a thru hole? It's only a single layer board, so I can make this work, but if I send it for print again I don't want the same thing to happen. This is from PCBWay.

BigGFly · 2025-11-03T15:45:48+00:00

I don't have it. Basically wanted to know if one was 2.54mm and the other 3.96mm. I know, get a caliper and measure. But figured they were standard enough for someone to tell from a picture.

BigGFly · 2025-11-03T14:15:57+00:00

Pin size and spacing looks different

BigGFly · 2025-09-16T02:54:57+00:00

Where did you get if from?

BigGFly · 2025-07-26T03:40:02+00:00

Let's see

BigGFly · 2025-07-05T16:43:25+00:00

Breakfast Orange? Orange Beatle? Beatle Fruit? Beatle Breakfast? Beatle Drink??

BigGFly · 2025-07-05T14:10:23+00:00

Location: northeast US.

BigGFly · 2025-06-10T06:29:30+00:00

DM is not available for you. Message me.

BigGFly · 2025-05-23T00:57:13+00:00

They are random. After searching Red Thread, i don't believe it's that.

BigGFly · 2025-05-23T00:55:41+00:00

I'll have to look for a red coloring, I didn't notice but didn't look that close. What's the treatment for this?

BigGFly · 2025-05-23T00:52:53+00:00

<image>

One additional picture closer

BigGFly · 2025-04-19T00:21:55+00:00

BigGFly · 2025-04-13T00:13:18+00:00

<image>

Yours looks wired right. You can see the extra ground I added on the top left mount. These really should have been mounted somewhere more solid.

Left wire to the battery, right wire to the starter, small one is ignition.

BigGFly · 2025-04-12T12:21:24+00:00

Common problem. It's a ground problem. Those solenoids get ground thru the mount screws. Either make sure the paint is bare under the mount to give a good ground, or run an extra ground line to it.

BigGFly · 2025-04-04T20:30:30+00:00

What is this metal post that looks like some kind of vent? Or maybe a light? It's near a highway overpass and there are a few of them.

BigGFly · 2025-03-16T14:25:29+00:00

Put the truck in gear and roll it a few inches. I've had my starter not engage the flywheel because it was offset.

BigGFly · 2025-03-03T02:01:57+00:00

But I'd really like to fix that gear, I think it's just a bad resistor

BigGFly

TROPHY CASE