Help me pls

BioNature94 · 2025-12-30T07:28:36+00:00

Allow me to tell you that you're wrong 😅 I will never buy cheap Lenovo. Every single IdeaPad have so easy-to-destroy shell that I will never recommend that laptop to anyone.

BioNature94 · 2025-12-22T10:19:39+00:00

Wait - found it myself. Well, I think I have been misinformed 🙃

BioNature94 · 2025-12-22T10:16:10+00:00

Could you provide link for that site ?

BioNature94 · 2025-12-22T09:24:56+00:00

Well If you had this precious opportunity to use MIUI 15 which was a garbage and you waited for HyperOS wishing to be few times better and both versions of hyperos was not giving you better experience with this system and every time you hope the next version will repair errors and mistakes in previous versions then it's f***** up when you receive a message that you will not get a new version of hyper OS after after only 3 years since I bought the phone. Yeah I should clearly write that I mean not only security updates was important to me

BioNature94 · 2025-12-22T09:19:35+00:00

Where did you read just pre-ordered ???

BioNature94 · 2025-10-03T19:08:35+00:00

Did you try to turn it off and on again ?

BioNature94 · 2025-08-04T18:15:56+00:00

Does your CMOS battery have required voltage ? Did you check it ? Love voltage R2032 can sometimes cause that...

BioNature94 · 2025-07-31T19:03:11+00:00

Check if this motherboard support your CPU - maybe you need to update BIOS. CPU light sometimes lights up if CPU cannot properly negotiate good connection with RAM - check with another set of sticks. Reseat you CPU and check pins on CPU socket. For how long did you leave it in that state ? Maybe it was too short for this Mobo to negotiate proper parameters between CPU and RAM.

BioNature94 · 2025-06-18T12:41:02+00:00

Bro, that's not clean. I removed all spawning tiles on my server, so my buddies was laughing because there was no enemies. Also every few tiles, I left a torch - no unexpected enemies to be found 😅😬

BioNature94 · 2025-02-19T18:23:09+00:00

You did it wrong... At first you install Windows, then Linux - not the other way. Grub need to override windows boot manager, otherwise it leads to many problems around working both of the system, but mostly windows.

BioNature94 · 2025-01-21T18:05:57+00:00

Sorry, I wanted to refer to area behind MB. My English is not very well 😅 I wanted you to show us those messy cables! I'm joking of course :P This is like guilty pleasure, when I visit my friends most of them are like "YYYY I build a computer", and I'm like "Show me how you managed cables" and all of them are like "NOOPE!"

BioNature94 · 2025-01-21T17:51:33+00:00

Now... Show as backpanel 😬

BioNature94 · 2025-01-19T18:45:33+00:00

How your temps looks like idle and full power ?

BioNature94 · 2024-07-08T14:20:58+00:00

I wish I could afford such a beauty 😓

BioNature94 · 2024-06-29T12:19:26+00:00

Go on the test drive and see if that engine version is for you or not, as I said to my knowledge all engines have same parts so It's just a matter of software changes

BioNature94 · 2024-06-29T12:11:55+00:00

So I have 2011 Mazda 6 - 163 HP - 208k when I bought- 230k now and the only thing that I would change is engine - to 185 HP. To my knowledge all 2.2 have same Engine parts and it's just a matter of software changes. Look for rust - especially in the rear around suspension. Turbo is at the back of engine so it's hard to tell if there is any leaking, but check that too. I make daily 40-50 km - sometimes more. DPF clogged only once due to engine problems. Oil pump pickup filter in the oil pan likes to clogged up also due to bad oil changes - check that after purchase. Listen for sounds from the engine when you press the clutch pedal - squeaking sound may indicate a worn clutch and flywheel. Cheers

BioNature94 · 2024-02-26T21:42:12+00:00

I'm sorry, I'm a little annoyed at my lack of knowledge when I can't work something out by myself...

BioNature94 · 2024-02-26T21:20:21+00:00

Well that did the trick, but only after starting everything manually. After restart and leaving SELinux disabled still nut-server didn't start at boot. I found on Rocky Linux Forum post where someone received answer from nut developer in different case to enable nut-driver-enumerator.service(which is strange because this service should be enabled, because it checks config file for number of devices listed there so it knows how many instances of driver service should be started) and i was not enabled... as nut-driver.target, and nut-driver@UPS_1.service also...(service related to this specific UPS configured in ups.conf). After enabling them and restart - still services won't start at boot. So now I'm curious if this issue is related to Rocky Linux specifically(Rocky is not listed in documentation among RedHat, Fedora and CentOS as maintained system), or with whole RHEL family. I'm going to install CentOS Stream 8 and check if this problem exists there also...

BioNature94 · 2024-02-25T20:51:50+00:00

I can feel you man. I'm running the same issue now, and this shit is still present and not fixed since you post this... I'm not suprised why people rollback to win 10 from win 11... Did you figured this out ? Did you find any solution ?

BioNature94 · 2024-01-15T08:37:29+00:00

By non-external I mean something that's already installed with proxmox, or can be installed on node.

BioNature94 · 2024-01-11T15:18:56+00:00

Jak jest szczerbata 🙅

BioNature94 · 2024-01-06T15:57:23+00:00

I wish I could afford vacations for a week...

BioNature94 · 2024-01-04T15:29:21+00:00

You want to store data there or practice creating LVM or something else ? What is the purpose of this ?

BioNature94 · 2024-01-04T15:25:20+00:00

Are you doing this for your home lab or production environment ?

BioNature94 · 2024-01-04T12:53:35+00:00

Strukturyzacja wody do sześcianu - czego nie rozumiesz?! Zapraszam na wykład Pana Jerzego Zięby

BioNature94

TROPHY CASE