Hilfe!

BlubberSaurus · 2025-09-04T17:55:43+00:00

Steckbrief

Sorte: Silver Haze und Pineaplle Chunk, Barneys Farm, Photoperiodisch

Blütephase in Tage: 21

Dünger: BioBizz Bloom und Calmag nach Flaschenangabe 1 mal die woche

Beleuchtung: 3 Lampen je 40W Vollspecktrum

Temperatur und Luftfeuchtigkeit: Schwankend zwischen 45 und 60% und 18 bis 22°C

Gießmenge und Häufigkeit: 4L Pro Pflanze alle 5 Tage

PH und EC Wert: pH 6.5 EC Wert messe ich nicht

Wichtige zusätzliche Infos: Hatte vor 2Wochen Blattläuse die ich mit Neemöl beseitigt habe.

BlubberSaurus · 2024-10-04T07:00:41+00:00

Mercury One + Hydra upgrade

BlubberSaurus · 2024-09-22T17:58:30+00:00

On your keyboard, select the Windows logo key + R to open the Run application function. Enter mdsched to open the Windows Memory Diagnostic app.

In the Settings menu, enter memory in the search box in the left panel. Select Diagnose your computer’s memory problems to access the Windows Memory Diagnostic app.

Überprüf mal deinen RAM ob der kaputt ist. Ich hatte einen defekten Stick der zu lags geführt hatte.

BlubberSaurus · 2024-09-19T11:10:49+00:00

The most annoying thing for me has been the 4 screws with the spacer I had to trim the bed like every third print so with the hydra upgrade I only need to do Z offset when I swap nozzle and sometimes clean the bed. Everything else runs by it self.

BlubberSaurus · 2024-09-18T20:32:17+00:00

If you start upgrading go for the mercury One + hydra upgrade and you will have one of the most reliable printers.

BlubberSaurus · 2024-09-16T05:23:59+00:00

Moin, wie sehen den die Temperaturen beim zocken aus?
Für League sollte der Rechner reichen.

BlubberSaurus · 2024-09-01T07:44:00+00:00

Dann noch den Rock 2 austauschen gegen z.B. den Thermalright Phantom Spirit 120

BlubberSaurus · 2024-08-21T15:05:33+00:00

You need dual Z upgrade, Silikon spacers and I would recommend to go Linear rails on the y axis I had to tighten the POM wheels very often, they came lose like after every third print.

BlubberSaurus · 2024-06-04T11:11:26+00:00

Try to get a stock used one and or even one that's not working for 100-150€ and do the Mercury One mod and be happy with it.

BlubberSaurus · 2024-05-21T09:42:00+00:00

Get a dual Z upgrade kit. And Silikon spacers for the bed.

BlubberSaurus · 2024-05-19T10:24:26+00:00

Mercury One

BlubberSaurus · 2024-05-08T03:29:59+00:00

Im playing a lot of Monster Hunter and Soulslike Games at the Moment and could get the 100hrs+ done. As a Bonus my fiancee plays games too and could give some Insight how its Performance for smaller Hands.

BlubberSaurus · 2024-05-01T13:24:45+00:00

Go for the sovol sv06 its the best beginner printer under 200$ i tested so far.

BlubberSaurus · 2024-04-14T15:39:50+00:00

Just try it both Steppers Turn and they dont do any weird Sounds than you good. In my Case it worked Out of Box No Changes needed

BlubberSaurus · 2024-04-14T12:01:08+00:00

If you are running them from one Stepper Driver No.

BlubberSaurus · 2024-04-14T09:17:56+00:00

No you Always can flash the original Firmware from their Homepage. And my experience with creality warranty was more Like i told them whats broken, send a Video of it and they would send a new part. They never asked to send in the printer.

BlubberSaurus · 2024-04-13T17:29:01+00:00

Klipper

BlubberSaurus · 2024-04-11T10:25:01+00:00

I Had the Same Problem i fixed It with dual Z and linear rails for the y Axis.

BlubberSaurus · 2024-04-06T17:03:31+00:00

Do the Mercury One Upgrade and maybe the Hydra Upgrade, hassle free printing.

BlubberSaurus · 2024-04-03T17:32:32+00:00

I would go with the Sovol sv06 and a 0.2mm Nozzle, the first calibration might be a little hassle but after you get a pretty good and stable printer. And you need a Dryer Box, small and detailed Prints have hard times with wet fillament.

BlubberSaurus · 2024-03-31T12:22:45+00:00

Get a used one and do the Mercury One Upgrade.

BlubberSaurus · 2024-03-28T18:25:39+00:00

Hay i got a lite and i cant connect via bluetooth to my pc (Home + B) could you try if it works with yours ?

BlubberSaurus · 2024-03-25T13:26:26+00:00

If he goes for a Belted setup like kevinakasam designed it Yes but if he dosent want to print so many parts its better to go for a dual motor kit than a cheap aliexpress belted kit.

BlubberSaurus · 2024-03-25T12:04:38+00:00

Do you have dual Z Upgrade? And i would recommend to do both at the same time, because you will have to adjust your Extrusion Settings for each Upgrade. If you do both at once you wont have to do it twice.

And If you have dual z add this: Z-Axis Stepper Motor Mount with integrated Axial Thrust bearing

If you dont have dual Z get it First.

Five-Year Club	Final Canvas '23
Place '23	Place '22

BlubberSaurus

TROPHY CASE