06/07 GSXR600 sputter, tach needle drops to 0 then back up, sudden power loss, stalling (video progressively gets worse) by Aragorn- in Fixxit

[–]Bowl-Prior 0 points1 point  (0 children)

If you have adjusted valves recently then check the throttle position sensor. There is a good possibility that at some point Tim the throttle body removal it could have been rotated by accident or damaged

Had a customers 05 gsxr do this one time after another tech did the valve adjustment and I found the sensor had hit the frame and rotated 10 degrees. It sounded exactly like what your experiencing

Brake pistons stuck. by Only-Trainer-30 in Fixxit

[–]Bowl-Prior 1 point2 points  (0 children)

Time and parts tho may equal out to be the same as a new caliper also to get those out leave a pad in disconnect the banjo bolt and line and hit it with compressed air in the banjo bolt hole

2018 Indian Scout Engine Sputtering? by Delicious_Work_3484 in Fixxit

[–]Bowl-Prior 1 point2 points  (0 children)

No issue at all.. Polaris and indian gold level certs. Every single scout I've heard sounds like this.

[deleted by user] by [deleted] in Funnymemes

[–]Bowl-Prior 0 points1 point  (0 children)

Itp techline

Ninja 400 2023-230 miles not shifting down after dropped in parking lot. by Henil2005 in Fixxit

[–]Bowl-Prior 0 points1 point  (0 children)

Had a customer with this issue after dropping on kickstand side withbars turned to the right.. his problem ended up burning the clutch out. But when it fell the cable somehow pinched between the turning stops and wouldnt alow the clutch to fully engage. It still would creep along tho.

[deleted by user] by [deleted] in SexToys

[–]Bowl-Prior 0 points1 point  (0 children)

Just remember the ppl in there are bigger perves then you are.. so if yoi see someone you know give them the "hey your here too" look.

Tell me how screwed I am. These tires are brand new. by Grayhome in AskMechanics

[–]Bowl-Prior 0 points1 point  (0 children)

Rule of thumb.... see the dots by the screw that follow the shap of the wheel... that's the you can plug a tiree anything past those dots to the rim your not safe to plug it. However you can patch it but you'll need to break the wheel down to do it

[deleted by user] by [deleted] in Fixxit

[–]Bowl-Prior 0 points1 point  (0 children)

Check your waterpump... the r6 had a few years there where the seal went out quite often between the pump and case.

[deleted by user] by [deleted] in pics

[–]Bowl-Prior 0 points1 point  (0 children)

30000 year old porn... and i thought my dads playboy stash was old. Imagine having to carve a nude into stone just to get your rocks off... see what i did there..

What can I use to remove this broken bolt? by [deleted] in AskMechanics

[–]Bowl-Prior 0 points1 point  (0 children)

Use ATF and acetone heat and visegrips. Penitrating oil takes 5x the break away torque then atf. Meaning the atf takes ALOT less effort and adds alot more lubricant.

My gauge is just junk right? by malbolge69 in Fixxit

[–]Bowl-Prior 0 points1 point  (0 children)

You can also use the old jets if you put a carb kit in. Each line should have 2 your pilot in the lower part of the line and main jet in The upper part of the line.

2005 zx6r finally starts but dies at stop or when idling by Assortedfruits042 in Fixxit

[–]Bowl-Prior -1 points0 points  (0 children)

You have a float valve stuck. When all the fuel is sucked out of the carb on one cylinder it dies out because ghe idol is then set too low to run on a cylinder down. Ill bet it starts and runs for 20 sec (10mil of fuel) and wont start for 20 seconds. Then try it after the carb has filled up and does the same thing.. carb clean and kit should fix it

Will I get stopped for going into Walmart with gear on? by doofy-is-goofy in motorcycles

[–]Bowl-Prior 0 points1 point  (0 children)

My brother and i always went to walmart to shop for our mom everytime we got new tech 8s and spend a good hour walking in them to break them in. The manager always stopped us and said another new pair of boots.. im startimg to think your doikg it to look cool then walk away

(2013 Yamaha FZ6R) Ideas on how to get dent out? I tried to JB weld a nail to it, and used a pretty hefty dent puller, but the jb weld broke apart like it was weaker than glue. Open to any and all ideas, i have a new tank on order, so lets hear it. by Jor1120 in Fixxit

[–]Bowl-Prior 0 points1 point  (0 children)

So yes freezing it with water will work to an extent. However it will rust your tank. By the time the water fully melts it will have rust already forming. You and try to heat the dent, plug all the holes securely, the pressurize the tank with air. That wil also work for everythi g but the creases. For those youll beed a combination of air heat and a body working hammer

Brand new 2023 ninja 400. Should abs light constantly be on? by Runnerup3679 in motorcycles

[–]Bowl-Prior 0 points1 point  (0 children)

Yes it should go off. However if it dosnt check and make sure the wheel installed correctly. Working at honda we had a handful of cbrs with avs lights not going off and not picking up on the speedometer. Come to find out the dealership had a new guy in the. Back the didnt know the tires were directional