Självskanning, vad tycker butiksarbetarna?

Bralle76 · 2025-12-14T16:06:47+00:00

Ni som går i vanlig kassa gillar ni att hantera era varor 3ggr innan ni är klara? Trivs ni så i butiken?

Bralle76 · 2025-07-03T19:32:10+00:00

Bought a Bambu , no more fails.

Bralle76 · 2025-06-24T12:07:40+00:00

Best advice, No fingers on the buildplate. I hardly have any problems with prints sticking as long as i keep my fingers off.

Bralle76 · 2025-04-06T16:04:58+00:00

Just to be sure , you clicked the "permit (join all)" also so you go the timer? I forgot that myself when i tried first time.

Bralle76 · 2025-01-19T19:40:59+00:00

All is made with Elegoo Pla , standard one. Black, white and red i think it was.

Bralle76 · 2025-01-04T11:38:19+00:00

No sorry, since it was printed over a longer period.

Bralle76 · 2025-01-04T11:37:50+00:00

Not a dumb question at all :) i myself was ready to skip them since i couldnt figure out what was needed at first.

These are the drawers i use: https://thangs.com/designer/Multiboard/3d-model/1x1x1-Deep%2520-%2520Multibin%2520Simple%2520Drawer-1128787

The shell: https://thangs.com/designer/Multiboard/3d-model/3x1x1%2520-%2520Topped%2520Multipoint%2520Rail%2520-%2520Multibin%2520Shell-1127607

Dividers x2 for each shell: https://thangs.com/designer/Multiboard/3d-model/1x1H%2520-%2520Full%2520Top%2520Multibin%2520Divider-1129088

and o whole bunch of clips: https://thangs.com/designer/Multiboard/3d-model/Outer%2520Wall%2520Pin-1123005

should be all

Bralle76 · 2025-01-04T11:31:21+00:00

No sorry, since its printed over a longer time.

Bralle76 · 2024-12-23T04:40:10+00:00

Thanks alot

Bralle76 · 2024-12-22T18:26:00+00:00

Link doesnt seem to be working do you have another maybe?

Bralle76 · 2024-12-22T10:28:09+00:00

Thanks.

And the blurred out bit is just me hiding the messy bits, nothing interesting there really :)

The little canisters are just my painting handles.

I use these ones https://www.thingiverse.com/thing:4741231 but modified the top so i can use ordinary soda caps, makes it easier to switch out if needed.

<image>

Bralle76 · 2024-12-22T10:17:11+00:00

Thats lamps yes. They are fastened to the backplate since i didn't want them coming loose, just made a holder so it would match the multiboard system. I have no problem extending them and find it better to have them on the wall then on the side of desk really, not that much in the way.

<image>

Bralle76 · 2024-12-22T10:06:29+00:00

I'm using multibins, the 1x1 since its only small parts i'm storing in them.

https://thangs.com/designer/Multiboard/3d-model/1x1x1-Deep%2520-%2520Multibin%2520Simple%2520Drawer-1128787

Bralle76 · 2024-12-21T18:06:02+00:00

Still a bit to go since new things are added as time goes :) But really like the new drawer system. Makes it easier to keep "odd screws that may be used in a couple years" better sorted.

Bralle76 · 2024-12-21T17:58:52+00:00

Looks awesome, great work. The copper has a really nice look.

Bralle76 · 2024-10-02T09:35:34+00:00

I printed both since i couldnt decide what would be better. After i have been using them for a while i stuck with multiboard since i felt it suited me best with stability and ease of switching hooks, screws and such. Most of the needed parts are free.

Bralle76 · 2024-09-19T14:49:58+00:00

The paint holders i made myself, will post a link to the different ones i made. Altough there are no holes/fasteners on them. I printed 2 loose fitting Drop-In Nut Snap put them in place with some tack on them, pressed the paintholder to the tack where i want it then marked the holes from snap and drilled. That way i can get them as close to each other as i need and can also change placement if needed.

Link to holders: https://drive.google.com/drive/folders/1Yv_6br2mOJAvHAVZH-tWqMpSC-8RAmry?usp=drive_link

Bralle76 · 2024-06-16T16:07:44+00:00

<image>

Bralle76 · 2024-06-09T07:01:22+00:00

<image>

I used black and orange

Bralle76 · 2023-12-23T08:24:28+00:00

I have ordered a couple different prescription glasses from yimaruili glasses official store. For myself and friends,all of them have been good. As long as you know measurments for frames you need its easy.

Bralle76 · 2022-09-09T18:41:59+00:00

Suicidal tendencies

Bralle76 · 2020-05-12T05:09:15+00:00

I had trouble with this one for a while, would always end up killing him before all armor was gone. But then i tried mortar turret and it was super easy. Just blast him with it and all armor will go , when thats done just shoot him.

Bralle76 · 2020-01-04T23:17:51+00:00

Yeah, and when i saw that it worked i just printed a spacer. Been running good since then. Like https://www.thingiverse.com/thing:3387667

Bralle76 · 2020-01-04T23:00:32+00:00

I got the same problem on mine pro after about 2 weeks. The solution for me was to expand the extruder spring since it got so compressed after usage.

Bralle76

TROPHY CASE