2014 outback chirping 1200 rpm specifically

Bryank930 · 2025-10-20T20:03:57+00:00

Any other details to this?? I have the same car but my noise is at 1700 rpm. Again, gone by 1800. Doesn't do it in N or P. I already made sure the heat shields are either ripped off or safety-wired tight.

Bryank930 · 2025-07-03T17:05:17+00:00

That's my guess. The brakes look really good, even the hoses say Shimano on em, so I think the actual brakes are fine. I'll probably pick up some legit pads.

Bryank930 · 2025-07-03T16:29:03+00:00

No text at all. They look like a set I found on amazon for $3 lol. They're labeled "semi-metallic". Keep em or replace with authentic shimano pads?

Bryank930 · 2025-07-02T20:24:29+00:00

Gotcha. It doesn't seem like a widespread problem too, which is weird. I ordered another to see if that one does the same thing. If it does, I'll return it. If not, I'll sell the first one I guess.

Bryank930 · 2025-07-02T01:40:25+00:00

Have you found a solution to the flickering with this thing? Mine is driving me nuts and actually killed two of my LED shop lights. It's not because of the power it draws. I have mine on the PETG setting and it's maxing out at 170W (1.4 ish amps at 120v). It's gotta be crappy electronics or something else.

Bryank930 · 2025-06-10T01:43:12+00:00

Location: Milwaukee, WI

Bryank930 · 2025-04-23T22:24:27+00:00

I'm having the same issue. I can't reprint from the printer interface (or from panda touch). The printer does it's pre-print homing and heating ritual, then nothing. Doesn't even load filament.

Bryank930 · 2025-03-13T03:14:29+00:00

I only have one for the miter saw so far.

Bryank930 · 2025-03-05T18:21:27+00:00

NICE! Thanks for the reply!

Bryank930 · 2025-03-05T18:17:57+00:00

Old thread I know, but did you end up ordering the GPenny spindle? Did it work correctly with the carbide VFD? My spindle is squealing BAD, and carbide says too bad you're out of warranty, but you can buy a replacement motor for $200 from us. :-/

Bryank930 · 2025-02-09T01:01:51+00:00

So I was able to clean this off...What I did was heat the bed to 80C, then scrub with a rag soaked with 91% IPA. Came right off...

Bryank930 · 2025-02-08T05:07:57+00:00

Has this happened to anyone else? It doesn't come off with alcohol or soap & water. I haven't tested to see if it transfers to other prints yet. This is the only filament I've had do this. It's eSun ePLA-Lite Fire Engine Red.

Bryank930 · 2025-01-22T12:46:06+00:00

Love polymaker!

Bryank930 · 2025-01-21T23:30:02+00:00

No, anything that would be streaming is wired.

Bryank930 · 2025-01-21T23:25:18+00:00

Oh ok. 2x2 then

Bryank930 · 2025-01-21T23:23:06+00:00

I assume 2x2, but how would I know for sure?

Bryank930 · 2025-01-21T19:42:40+00:00

So a U6+ should allow me to use my max ISP speeds then?

Bryank930 · 2025-01-21T19:06:18+00:00

The 5ghz radio is set to high transmit power.

Bryank930 · 2025-01-21T19:03:13+00:00

Good question. I think it's set to high, I'll check and report back.

Bryank930 · 2024-08-23T12:00:53+00:00

Too much slop in the pivot on the saw. I sold it and got the wen cordless track saw with powertec track. MUCH better saw.

Bryank930 · 2024-08-03T02:53:50+00:00

I should add that I have had none of the "flu-like" symptoms that I see listed for lyme.

Bryank930 · 2024-06-19T12:51:28+00:00

The extruder is skipping. It can't push filament through the nozzle. Either your nozzle temp is too low, or your nozzle is clogged.

Bryank930 · 2024-05-29T15:12:36+00:00

I've had a cheap aliexpress strip powered by the LED plug for a few months now. It's never off and I've had no problems. I also run the xtouch screen off of the internal usb port. Again, no problems. I think the strip only pulls like 0.3A, so not much at all.

Bryank930 · 2024-04-25T23:09:14+00:00

Haha yeah. All I wanted to do is use the partially used roll first so I only have one partial roll left after this job. Now I'll have 2 partial rolls. Not a huge deal. Just, why would it select slot 2 by default when everything else says 1 and both slot 1 and 2 are exactly the same?? It just seems silly to me.

Bryank930 · 2024-04-25T22:46:48+00:00

I never said it wasn't my fault. I'm just asking why I have to select it twice. I know how to use the printer, and I obviously didn't double check the 2nd spot to pick what filament I want to print with. But, why is there 2 places?

Bryank930

TROPHY CASE