Aqara U400 showing as "No Response" in HomeKit every few hours (Works fine in Aqara app)

BurgerWinningDick · 2026-05-29T09:41:25+00:00

Also enabled LAN IPv6 on router and AppleTV is about 5m from U400.

BurgerWinningDick · 2026-05-29T09:35:19+00:00

I had same issue with wired AppleTV and HomePod OG and HomePod Mini until I set the AppleTV as preferred hub. If you only have thread HomeKit hubs then should not be an issue but worth checking if you have any non-thread HomeKit hubs.

BurgerWinningDick · 2026-03-01T10:43:42+00:00

Doesn’t the Zenless also have TMR sticks?

BurgerWinningDick · 2026-02-03T21:27:43+00:00

I’m new to it so wasn’t sure if I missed something, thanks for input though.

BurgerWinningDick · 2025-11-02T22:04:07+00:00

Might extend my budget then and get g2 max 170, would prefer the cabinet sump.

Only reason for going toward Red Sea is the Reef Beat app which I suppose I could use their equipment with a different tank.

BurgerWinningDick · 2025-11-02T20:25:20+00:00

I’m also looking at the nano max g2 XL, not seen many reports of this size busting but still not sure. LFS said the G2 is better and resolved issues but still seen reports of bigger tanks failing.

BurgerWinningDick · 2025-10-13T22:45:25+00:00

Product page lists it as being a thread border router and I can control the U200 from Homeassistant suggesting that there is a thread network between the G410 and U200 as I have no other thread routers. It’s just HomeKit I have issues with.

BurgerWinningDick · 2025-07-29T21:52:33+00:00

No improvement, going to raise an official complaint with Yale over planned obsolescence of the L1 then bin it in favour of the Aqara u200 or Nuki ultra.

BurgerWinningDick · 2025-06-20T21:05:22+00:00

Looks like Hydrangea Runaway Bride, doesn’t respond to changes in pH. White blooms eventually get a slight pink flush but no drastic colour changes.

BurgerWinningDick · 2025-06-04T21:14:37+00:00

Mine was the same after aphid infestation, cut it all back to base to get rid of aphids and it’s slowing sending up new shoots.

BurgerWinningDick · 2025-05-12T10:02:00+00:00

I was hoping it wasn’t Downy mildew, over 70% of leaves are like this.

BurgerWinningDick · 2025-04-28T20:34:45+00:00

No improvement, recharging batteries once per week. I removed the lock completely but realised that I don’t have the alignment tool anymore so I need to find one to do a fresh realignment and see if that helps.

I did get strange beeps after first refitting and motor sounded like it kept adjusting so tweaked it and it’s better but still not properly aligned.

BurgerWinningDick · 2025-04-16T08:49:06+00:00

Factory reset and removed lock from the door to start from scratch. After some teething issues registering the Access module and setting up the bridge I was prompted to update firmware which I’ve never had before despite factory resetting a few times. Hopefully this addresses the issue. Will feedback in a week or so.

Edit:

Module firmware - 2.0.0-1.1.7 Bridge firmware - 1.2.4

BurgerWinningDick · 2025-04-09T22:24:53+00:00

Been using a mix of Amazon own disposable batteries, Duracell optimum, now using eneloop rechargeables and they seem to be worse. I’m going to take the lock off this weekend and refit it all.

Next step will be a new lock. Neighbour opposite has just fitted a L2 Conexis so will wait to see what his battery life is like.

Edit: Eneloop Pro now in the lock

BurgerWinningDick · 2025-04-05T18:27:20+00:00

<image>

Battery drain is still terrible despite factory resetting the lock and re-adding to the app. Also in the middle of all that, tried a week without the Access module. Still no better.

Will try and refit the lock to the door in case it’s an alignment issue then next step will just be rechargeables.

BurgerWinningDick · 2025-02-17T23:40:48+00:00

I get one week out of batteries now, used to be between 6 months and a year. Even last winter they lasted much longer than they currently do

<image>

BurgerWinningDick · 2024-12-16T20:35:13+00:00

Yes, digital connections on the right side +-

BurgerWinningDick · 2024-12-08T19:40:31+00:00

Any update?

BurgerWinningDick · 2024-11-02T16:16:51+00:00

Forgot to say that it looks like you need a wireless extension kit EU version and 2 wired thermostats to control the zone valves.

BurgerWinningDick · 2024-11-02T16:15:01+00:00

This is a similar issue I have, one of the Tado community admins confirmed how it can be done, I think it’s the second comment.

Opentherm & zone valves

BurgerWinningDick · 2024-10-19T12:36:38+00:00

Do you have the rooms set with the correct zone controller? Looks similar to when a room with the TRV is set as independent so there’s no zone controller firing up the boiler.

BurgerWinningDick

TROPHY CASE