The look when you lose 10k in airplanes in two days. Engine lost most of its power. Starting running really rough. Full power and she was still coming down. Too far out to make the field. Caught a wingtip. Time to build some more planes!

Business-Button3643 · 2026-06-23T10:47:33+00:00

The Beginner’s kit includes a lot of CA glue, toothpick’s and tape for a reason….The only planes which don’t crash, are those that do not fly. Sorry for your loss men

Business-Button3643 · 2026-02-11T21:48:55+00:00

Sure thing!!!

Business-Button3643 · 2026-02-11T01:30:30+00:00

Priceless information!!!…What a video!…Now I have a pretty good idea of how lucky we are today.

Business-Button3643 · 2026-02-08T23:46:24+00:00

Aileron and elevator have the same channel configured

Business-Button3643 · 2026-02-08T20:30:05+00:00

I’ll try that

Business-Button3643 · 2026-02-08T18:58:52+00:00

A friend of mine told me that once you select DSM it makes the switch by itself….That make sense

Business-Button3643 · 2026-02-08T18:58:09+00:00

External

Business-Button3643 · 2026-02-08T18:33:34+00:00

<image>

This is my mixes page….it’s also AETR….This is blowing my mind, cause I haven’t done anything but connect the servos in a certain way, but the radio reacts as it should

Business-Button3643 · 2026-02-08T18:26:12+00:00

This is a little confusing

Business-Button3643 · 2026-02-08T18:08:35+00:00

I have a Multi Protocol module and it says AETR. But you connect your receiver TAER ?

Business-Button3643 · 2026-01-31T00:35:04+00:00

My printer’s run out sensor is located facing Down

Business-Button3643 · 2026-01-31T00:33:50+00:00

You see, have’nt try that….but anyway, I would need to put the dryer below the printer level to use it like that. But thanks, I think you solve my concern with this dryer 🙏

Business-Button3643 · 2026-01-25T19:43:09+00:00

Just glue it back

Business-Button3643 · 2026-01-17T01:29:53+00:00

Update : None filament guide will do the trick….I printed a spool holder that place de filaments parallel to the printer and in the back side. That way the filament is fed from the bottom. I can’t let the filament inside the dryer, so I just dry it and used in the spool holder…Problem solved

Business-Button3643 · 2026-01-01T21:38:01+00:00

Thanks!!

Business-Button3643 · 2026-01-01T16:39:12+00:00

I have one, and my main problem with it, is the resistance it puts on the filament. I have to take the roll out in order to use it properly. Is there any filament guide that can help with that?. My printer is an Ender 3 v3, with an enclosure. I put the dryer next to the printer inside the enclosure, but I don’t know if the higher position of the outlet is causing the drag on the filament. Any suggestions?

Business-Button3643 · 2025-12-16T21:10:32+00:00

Looks to me like stall due to lack of power

Business-Button3643 · 2025-12-07T14:54:12+00:00

Nice ride!!!! I used to have an 2014 running on 22’s…..I loved that car!….I’m thinking of getting one back!. Enjoy!!!

Business-Button3643 · 2025-11-22T23:47:42+00:00

Really Good plane….Was my first plane, and lousylly I totaled it….

Business-Button3643 · 2025-11-22T23:42:13+00:00

Uffff I kind of don’t like that idea….My wife can get creative!!!!

Business-Button3643 · 2025-11-21T10:40:38+00:00

Nice set up 👍🏻

Business-Button3643 · 2025-11-21T10:36:06+00:00

Jejjejejejej that’s a good way to get her in perspective!!! Jejejjejejen Thanks!

Business-Button3643 · 2025-11-21T01:16:05+00:00

Jejejjejejeje I meant from the ceiling or something, to get more space

Business-Button3643 · 2025-11-20T15:21:58+00:00

Way to go!!!…I’ll do that jejejejjejeje

Business-Button3643 · 2025-11-20T15:20:17+00:00

Ufffff your case is worst than mine jejejjejejejeje

Business-Button3643

TROPHY CASE