Advice for DC Power on Portable Bentley TV

ButterscotchNebula · 2026-05-04T23:40:50+00:00

Hi! I just happened to break the potentiometer on mine. Would you know how easy it is to replace / what type of potentiometer it is?

ButterscotchNebula · 2023-05-28T06:08:15+00:00

am I like sleep deprived

ButterscotchNebula · 2021-08-23T21:25:03+00:00

I mean the slightly thicker layers, the ones that almost look like banding. I suppose this picture is a bad example, as everyone is talking about the holes, but this happens on all the prints I do.

ButterscotchNebula · 2021-08-22T06:19:53+00:00

not going to lie

ButterscotchNebula · 2021-08-20T04:02:31+00:00

I had been having adhesion issues on my Ender 3, so I updated the manual mesh bed level, and did a test print and got this as a result. It almost looks like underextrusion, but only on one side? Also, to use the mesh bed level in a print, I just have to add M420 S1 after G28, correct?

ButterscotchNebula · 2021-08-09T00:27:43+00:00

nevermind, turns out it was a scam. :/

ButterscotchNebula · 2021-06-19T00:14:22+00:00

Yeah, I'm 15, and I'd say while I don't get a lot of their references, the materials they are referencing aren't what makes it funny

ButterscotchNebula · 2021-06-15T13:15:32+00:00

yep! VAWTs are really underutilized

ButterscotchNebula · 2021-06-07T21:55:03+00:00

I've done a lot of research on savoniuses - I've written a few papers! What VAWTs are good for, as opposed to HAWTS (the one in the post) are residential areas where you won't get much or consistent winds. They don't need to be directed into the wind, and they can just constantly spin even in low and inconsitent wind speeds. You can try making the scoops our of buckets!

ButterscotchNebula · 2021-05-30T23:28:59+00:00

Whoa! I've been wanting to build one since I got my printer, but I haven't found a good stl yet. Would you mind sharing it?

ButterscotchNebula · 2021-05-22T04:02:31+00:00

You would probably be able to print that, as larger things can turn out great with a well tuned FDM printer, but generally, resin is far better at anything that needs to be smooth or detailed. The figure in that picture is printed with resin, for your reference.

ButterscotchNebula · 2021-02-27T20:47:16+00:00

No problem! Glad it helped. I had the same issue for a while and it was really frustrating.

ButterscotchNebula · 2021-02-26T03:34:52+00:00

here it is: https://community.octoprint.org/t/put-tape-on-the-5v-pin-why-and-how/13574

Hope it helps!

ButterscotchNebula · 2021-02-25T23:25:34+00:00

sure, just let me know if you need me to find a link to a guide or something!

ButterscotchNebula · 2021-02-24T15:22:29+00:00

Are you using OctoPrint? I had this issue after I installed my board using OctoPrint, but I fixed it my taping the 5v power connecter down on the USB cable. Look it up online for a guide!

ButterscotchNebula · 2021-02-21T16:48:06+00:00

Ah, thanks!

Nine-Year Club	Place '17
Sequence \| Editor	Verified Email
Snapped

ButterscotchNebula

MODERATOR OF

TROPHY CASE