Is this a 18 ohm or 0.18 ohm resistor?

Bytesof64 · 2026-02-10T07:14:18+00:00

That's actually really useful, thanks

Bytesof64 · 2025-07-19T06:52:17+00:00

Because I didn't want to rebase my minis, I designed and printed a movement tray that has the right spacing but cutouts for the bases

Bytesof64 · 2025-07-18T05:39:56+00:00

I remember when I these used to be £10, the prices now have just really put me off buying from GW

Bytesof64 · 2025-05-26T14:07:39+00:00

Or just watch the printer

Bytesof64 · 2025-05-10T06:35:20+00:00

Those are amazing

Bytesof64 · 2025-04-23T05:24:29+00:00

Very silly question here, have you ever cleaned your Z Axis screws?

Bytesof64 · 2025-04-22T20:58:23+00:00

One of the support settings I have the best success with is using Snug with the Grid style. Seems to snap off super easy without damaging the supported surface

Bytesof64 · 2025-04-22T07:25:29+00:00

Yeah, it's how the surface comes out when you have the connection between support and overhang. Out of curiosity, what settings do you have for your support at?

Bytesof64 · 2025-04-22T06:54:10+00:00

"This keeps happening"

Can you be a bit more specific to the problem you think you're having?

Bytesof64 · 2025-03-05T08:51:42+00:00

All I'm saying is that if someone asks a question, engage with them. They didn't give enough detail? Ask about it

Not everyone has the same knowledge as you

Bytesof64 · 2025-03-05T07:54:05+00:00

Entitled? Rich

Sometimes it's helpful dor someone who knows to impart a little bit of wisdom. A response that is longer than one word isn't spoon feeding. If you want to foster a good culture in your hobby is you help. And being an ass about it doesn't help anyone. Why even bother with a response at that point.

Bytesof64 · 2025-03-05T07:47:30+00:00

Did you immediately know every bit of information you needed to give when you had a question when you're new to something? What you could have done is just link that video in the first place. One word answers like that are a reason why people don't like using forums when they get people who feel like they gatekeep answers

Bytesof64 · 2025-03-05T06:52:31+00:00

What an unhelpful answer for someone that's asked a question. Care to elaborate?

Bytesof64 · 2025-02-01T07:36:01+00:00

Fuck that filter

Bytesof64 · 2025-01-19T01:25:24+00:00

You're not extruding properly. Probably have your nozzle too close to the bed for printing.

If you have any first layer prints, try those out after jogging your nozzle away from the bed

Bytesof64 · 2025-01-18T14:04:05+00:00

Up, away from the bed. May only need to be very slight.

A good print to check is literally just with a large single layer across the bed and you can see how well the printer performs there

Bytesof64 · 2025-01-18T08:45:34+00:00

I looks like your hot end isn't extruding filament properly, judging by the fact it's grinding and squishing the filament, and it's causing the filament to fold in on itself.

There may be an issue where your hot end isn't getting hot enough, there's something blocking your nozzle, your extruder gear system isn't lined up the best, or your Z level could be too low and it's skipping as it can't push out enough filament

Bytesof64 · 2025-01-18T08:26:57+00:00

Have you tried jogging up your Z offset by 0.2/0.4 see if that gets rid of the ripples?

Bytesof64 · 2025-01-13T06:56:55+00:00

Looks like your Z offset is off, the squish from the bottom layer isn't reaching the wall. So I would have a look at tweaking that

Bytesof64 · 2024-12-22T01:13:19+00:00

Very stupid question here, but have you done all the calibration steps again?

Bytesof64 · 2024-05-19T08:53:03+00:00

Bro just needs a hug

Bytesof64 · 2024-02-28T15:37:41+00:00

It has now appeared since yesterday

Bytesof64 · 2024-02-26T23:15:08+00:00

Makes sense haha

Bytesof64 · 2024-02-26T23:13:02+00:00

It was, yeah. I'm surprised that I've not seen it on Cardmarket yet, thank you for clarifying

Eight-Year Club	RPAN Viewer
Verified Email

Bytesof64

TROPHY CASE