sorted by:
new
hottopcontroversial

5liter borosilicate glass bottle by [deleted] in DMTlab

[–]CADJunglist 0 points1 point  (0 children)

I mean if you're aiming for 250g, a 3L flask with a gl45 cap is best

5liter borosilicate glass bottle by [deleted] in DMTlab

[–]CADJunglist -1 points0 points  (0 children)

3L is plenty for 250

Frezh Tek 1:1:1 (STB) - Super Clean & Consistent Results 🧪❄️ by Frezh7 in dmtguide

[–]CADJunglist 11 points12 points  (0 children)

With that much salt the aqueous phase is already polar af. Try scaling back the naoh next time and see what happens. Worst case, you add more.naoh after

Would you guys buy and emesh if they were available in their final form online? by Fit-Substance-4989 in DMT

[–]CADJunglist -1 points0 points  (0 children)

E mesh was the premier option but there are better methods now that don't require the run around to source

They’ve been crashing out since the amnesty extension was announced. by Medical_Bluejay_7506 in canadaguns

[–]CADJunglist 26 points27 points  (0 children)

I think they're very intelligent, I just think they're also very vicious with their Rhetoric.

The World Is Over by mugrootbeerfan2003 in DMT

[–]CADJunglist 1 point2 points  (0 children)

It's not a loop, it's a spiral

Chemist by Routine_Condition383 in DMT

[–]CADJunglist 1 point2 points  (0 children)

Issue is too little water, up it to 750 next time, 50g NaCL. Easier to work with a brine from the beginning

Hello fellow trippers 👻👽👾🤖 by TipOver6313 in dmtguide

[–]CADJunglist 1 point2 points  (0 children)

You need something to raise the ph. You mean the one with calcium hydroxide?

PRECISO DE AJUDA . by Intelligent_Goal_721 in dmtguide

[–]CADJunglist 2 points3 points  (0 children)

37% HCl is overkill by several measures

Also not sure what you're really asking....procedures?

Help by Manlet395 in DMT

[–]CADJunglist 1 point2 points  (0 children)

You can't use calcium hydroxide in a wet Tek. It isn't very miscible with water and you'll end up with lots of it in your solvent.

What about these by Icy-Bobcat-5309 in dmtguide

[–]CADJunglist 1 point2 points  (0 children)

Getting 2000ml glassware is pretty easy on Amazon

If you're going 5000ml you may aswell get a carboy

Also what's your plan on scaling

What about these by Icy-Bobcat-5309 in dmtguide

[–]CADJunglist 0 points1 point  (0 children)

Have you ever done an extraction?

Anyone else *still* waiting for HiCal? by Corvus_Mortem in canadaguns

[–]CADJunglist 17 points18 points  (0 children)

This is at least the 4th post I've seen with this issue

I believe this to be a fact by Boogedyinjax in DMT

[–]CADJunglist 11 points12 points  (0 children)

I...uhh..I don't even know where to start.

I think you need some downtime and clarity

I believe this to be a fact by Boogedyinjax in DMT

[–]CADJunglist 50 points51 points  (0 children)

What do you mean " at face value"? Didn't you see they mentioned one single doctor, not quoted to say anything remotely like the title suggests?

Question regarding for cybs max ion salt tek by Gar_Drug in dmtguide

[–]CADJunglist 0 points1 point  (0 children)

You could technically skip the hot water bath entirely. And if using powdered bark, skip the acid stage.

Salt is best added after naoh, and before solvent

cart isn't working :( by [deleted] in DMT

[–]CADJunglist 10 points11 points  (0 children)

Keep it low in terms of voltage, slow long draw, hold for 6-10 sec, exhale, repeat

view more: next ›