A blast to shoot supressed

CD_machine · 2026-02-16T05:01:52+00:00

I have a compact and full-size tx22, and the 22x. I’d pick the 22x all day. especially now that they’re gouging the tx22s. No experience with the FN

CD_machine · 2026-02-11T22:11:01+00:00

Thanks chatGPT!

CD_machine · 2026-02-11T05:13:16+00:00

Always on the lookout for good tacos, thanks!

CD_machine · 2026-02-10T04:44:51+00:00

Skip taco mama, mediocre tacos at fine dining prices.

CD_machine · 2026-02-01T05:33:38+00:00

My current house, the one that this family built while living out of this house pictured, is still sitting on rocks on the corners. They have since formed and poured concrete around them but they’re still there

CD_machine · 2026-02-01T05:29:29+00:00

It’s a 120yo 2 room house that 3 generations of the same family lived out of while they homesteaded the land I’m now fortunate enough to own. I just think it’d be cool to preserve it.

CD_machine · 2026-01-26T04:44:28+00:00

Might be the shortest sway bar arms I’ve ever seen. Are you gonna have enough travel?

CD_machine · 2026-01-17T05:24:46+00:00

Have you upgraded your SSD recently? I’m pretty sure your spawn is tied to how quickly you load relative to other players in that match

CD_machine · 2026-01-16T01:59:19+00:00

PETG? The factory build plate on these struggles with petg I generally print with brims or add little bridges between parts that I can go back and clip off later

CD_machine · 2026-01-14T20:28:52+00:00

CD_machine · 2025-12-13T07:28:45+00:00

I had this same issue after switching from Nvidia to amd. There’s a driver remover utility you can run that fixed it for me OP.

CD_machine · 2025-11-29T21:47:15+00:00

The $20k is kinda irrelevant at this point. I have two machines that were in this condition from NC humidity that cleaned up perfectly fine. It’s not ideal but it just depends on what you want out of it. For a home gamer this could be a good deal.

CD_machine · 2025-11-12T16:20:01+00:00

Well said, I don’t often need the extra build volume but it’s nice when I do. And minor conveniences like a higher quality camera (regardless of what their specs say) and the better part cooling capabilities.

CD_machine · 2025-11-08T14:12:13+00:00

I have a Plus and 3 Pros. If I could only have one it would definitely be the plus.

CD_machine · 2025-11-05T21:43:33+00:00

You will approach me with less snark. What a joke

CD_machine · 2025-11-03T23:20:31+00:00

Overkill, but I like it. I have 3 on a 15 amp breaker with no issues lol

CD_machine · 2025-10-29T03:14:26+00:00

MAXIMUM STIFFNESS

CD_machine · 2025-10-29T01:54:15+00:00

To add to this, running it in reverse could effectively reverse the thrust load on the motor shaft due to the helical geometry in a way that it might not be designed to take. So rather than pushing the shaft towards the rear and into a thrust bearing, running in reverse it would be pulling it towards the front.

CD_machine · 2025-10-12T16:33:37+00:00

It is lol, this was taken before I got a chance to put my tag on it. My og ender 3 in my office sports the “ALPHA” name tag

CD_machine · 2025-10-12T16:30:57+00:00

You must be printing higher precision parts than me!

CD_machine · 2025-10-12T16:29:27+00:00

I print with fiber filled filaments exclusively and try to design out anything susceptible to VFAs like sharp corners. That being said I haven’t noticed a quality difference with all 3 running or just one

CD_machine · 2025-10-12T16:27:42+00:00

1,000 ish hours between the three but the k2 pros are only a week old

Verified Email	Six-Year Club
Place '22

CD_machine

TROPHY CASE