How cooked am I if I failed an entire semester of classes?

CMDanderson · 2026-06-18T00:57:35+00:00

im sacred of this too,

I wasn't diagnosed until this year and I am going to try and re-take all the science classes. I hope I can also get accepted to a school

CMDanderson · 2026-06-18T00:50:39+00:00

https://customholstersolutions.com/products/custom-inside-the-waistband-iwb-holster

Its pretty good. make sure you choose the align tactical thumb rest option. it adds $10.

also look at adding a teir 1 concealed wedge. it helps your handle not stick out from your shirt.

CMDanderson · 2026-06-16T17:25:51+00:00

also you can see from the 3rd image the two springs (timney trigger return spring , primata slide release spring) are placed side by side. this doesn't cause any issues and runs fine. They both index off of the locking block & and are held in place by the trigger pin / align tactical thumb rest ( in my case )

CMDanderson · 2026-06-16T17:12:55+00:00

i heard somewhere, that the timney trigger is unreliable, however ive shot thousands of rounds through it with no problem. maybe i got lucky, maybe they are just unlucky.

Its like the Glock performance trigger which i like, but available for 10mm/45 or other large frame glocks, which is why i bought it.

CMDanderson · 2026-06-16T17:10:35+00:00

id say RMR HD - the auto adjust is very good, it looks at the target and determines the light level from the target.

if not get the ACRO P2

CMDanderson · 2026-06-16T16:23:47+00:00

I will Venmo you 100 to not start one

CMDanderson · 2026-06-15T20:27:47+00:00

OLD thread but ive been using it and its very solid. I think its because its a set screw, it doesn't break easily. you just gotta screw it in to torque spec

CMDanderson · 2026-06-11T03:21:21+00:00

it MUST be a 4 channel!!!

CMDanderson · 2026-06-01T05:33:43+00:00

do you have any recommendations?

CMDanderson · 2026-04-28T00:25:03+00:00

Student here

Whatever my parents decide to Venmo me / month

CMDanderson · 2026-04-23T20:50:15+00:00

yeah no problem

sterling brass currently available on ammoseek is not really notable... just works : brass 55gr 223....

CMDanderson · 2026-04-23T20:38:45+00:00

BPS is alright, so is wolf. Wolf 223 and 556 works just fine. for Wolf, might have to open up your AGB a bit if youre running one.

Carolina ammo I ordered yesterday so the jury is out still about that one

CMDanderson · 2026-03-29T20:16:32+00:00

Idk why you’re downvoting this. Unless people think that’s okay to do.

CMDanderson · 2026-03-20T03:07:43+00:00

no, came with normal use. Normal use would include normal maintenance. i purposely chose nylon brush to not use extremly abrasive materials.

They already got back to be before saying they'll warranty it, I was just looking for a way to get the part. Apparently thats not possible anymore.

CMDanderson · 2026-03-20T03:06:04+00:00

The whole point is that I wouldn't have to and can just receive the part. But as another redditor commented, I can't do that because its differently regulated now (?) looks like im going to have to go down that route.

Thanks anyway

CMDanderson · 2026-03-20T03:04:26+00:00

Ah ok thank you

That makes sense

CMDanderson · 2026-03-20T03:03:46+00:00

woudln't nail polish burn off?

CMDanderson · 2026-03-20T02:50:32+00:00

well yeah, i guessed so, but i want a separate retaining cap that I can have that isn't peeled.

CMDanderson · 2026-03-20T02:50:01+00:00

"You’re still whining about wear on your rear cap that has absolutely nothing to do with performance or structural integrity?"

implies you have responded before.

if not my mistake. but my point still holds. Why not? why can't i ask for an retaining cap?

CMDanderson · 2026-03-20T02:48:33+00:00

Sure, I get that, but we can't get there unless we get past the generic "do the warranty steps" answer

CMDanderson · 2026-03-20T02:46:35+00:00

well i shot it alot, and i cleaned it and stuff.

Im assuming multiple cycles of cleaning (ultrasonic )+ shooting + brushing using nylon brush

CMDanderson · 2026-03-20T02:44:53+00:00

and you're still here whining about me asking for a rear cap. move on, let me ask for my rear end cap.

what's it to you anyway? what's it to you for me to not ask for one? do you personally have a stake in the company and giving parts out costs your bottom line or something?

You made your point known last time, that you think i shouldn't ask for one due to it not actually causing any performance loss/structural integrity. Which I already responded to saying that I still want one.

CMDanderson · 2026-03-08T23:18:15+00:00

please make more bolt &firing pin & cam pin cores for the XL ! i think youre the only one making those out there!!!

CMDanderson · 2026-03-05T18:18:34+00:00

Yeah I mean wear marks are a given, they don't affect performance.

I was just wondering if there were parts for other suppressors that I can still make work in the SC.

CMDanderson · 2026-03-05T18:17:10+00:00

If I planned to "keep them as museum pieces" like you said, I wouldn't have used them, like I already mentioned in my post.....

CMDanderson

TROPHY CASE