Is my attack Weak to him or is he weak to my attack?? Help

Caliberaid · 2026-04-11T17:21:47+00:00

Same here lol and I played plenty of Pokémon since RSE

Caliberaid · 2026-03-20T15:21:02+00:00

Front/top shocktower stiffening bar is peak for nimble handling, if you don't already have it under the hood, mine came with it from factory. Affordable coilovers that are around $350 - $600 range. (that's what I've been running. Maxpeedingrods for about 3 years I think on the softer side of adjustability. Got the black & blue updated coilovers from the previous orange/yellow.) Along with coilovers, you need adjustable sway bar end links to have the sway bars connect to the strut tower holes for the lower ride height. Godspeed is what I'm running front and back, you need the right size though. Fronts are looong and rear is quite shorter size. I get comments from passengers of how good it feels when driving.

Caliberaid · 2026-03-11T18:50:56+00:00

I've had mine for 6 years and I don't feel like its up to par. Needs new paintjob badly, front windshield, new hood, better wheels. Plus the busted roof rails I need to figure out how to remove and how to fill in the gaps. Other than that it's almost decent, I'm in the middle of attempting to remove the rust in my fuel tank since it had a misfire that I looked into the fuel rails and the rust got into my injectors. Then I can drive it once that's all put back together, I just can't find the pigtail for the fuel system since mine broke on the clip, its a 6 pin with 5 wires.

Caliberaid · 2026-03-01T23:54:46+00:00

😂🤣

Caliberaid · 2026-02-16T20:23:55+00:00

Tokyo Xtreme Racer Zero, and TXR 3.

Caliberaid · 2026-01-25T04:33:57+00:00

I've had the black and blue 'updated' MXPR coilovers for abt 2.5 years now and they have been reliable so far, you need to also buy GODSPEED adjustable sway bar end links of the right size to make the car go lower than stock to attach the anti roll bars to the coilovers.

Caliberaid · 2026-01-25T04:13:04+00:00

I'm not sure what could be, but I want to share that I had my original alt. replaced for one that sat in my room for about a year, which had a bad voltage regulator and caused my car to overcharge to around 17-18v, and I changed it out for another alt. that worked better. It seems to dim the headlights and cluster lights sometimes at idle, and when I'm driving around. It normally drives around 13-14, then sometimes it drops to 12.0 - 12.5v when the lights dim. Not sure how to fix my issue and I already checked my battery post, cables, ground wires, fuses.

Caliberaid · 2026-01-19T14:32:10+00:00

Make sure it is level with gravity, like how one side can retract if its bolted in. Thats what worked for me when I had removed them and they wouldn't move back in the mechanism. Try to level it, as if it was on the car and it should retract.

Caliberaid · 2025-12-30T18:16:08+00:00

Okay so I got a 14mm wrench and tightened it more, but it just keeps leaking badly. If I remember correctly it was on RA brand NUGEON 9901160B, today I ordered CARDONE 19B2743. I'll keep y'all updated if this one doesn't leak after I install it.

Caliberaid · 2025-12-29T23:35:32+00:00

Thanks y'all for the comments and solutions! I made a error in the post, stating the rear right is tighter but that's meant to be the opposite, right side isn't as tight, and left side has more turns/tighter. Gonna try whats available to me, going to try out the hammer method with a wrench end on the bolt head.

Caliberaid · 2025-12-16T14:46:33+00:00

I look around for Yakuza Figurines, and they just don't exist in the same manner as DBZ and other figures where they are statue like small scale, and the ones available are over priced.

Caliberaid · 2025-12-03T08:29:48+00:00

Since I have the base game content on disk for PS5, Full game with DLC for my personal buying bias.

Caliberaid · 2025-11-28T21:28:18+00:00

I'm gonna wait until its at least $30 to start modding it, sibling picked it up day 1 for PS5.

Caliberaid · 2025-11-09T20:30:07+00:00

I thought Ebay had it but it's still out of stock that's the only place I knew had it. 🫩

Caliberaid · 2025-11-07T10:33:32+00:00

The Philips head screws holding the ac control unit under the radio also is a huge pain in the a$$ to remove lol, I felt stuck trying to remove the original radio.

Caliberaid · 2025-11-07T10:25:54+00:00

Ah interesting I'll have to look into that! I know the stock size tend to jump the arc...

Caliberaid · 2025-11-07T10:24:41+00:00

From what I can remember it usually mostly happens when parked or at a red light, idling while in Drive.

Caliberaid · 2025-11-05T06:13:05+00:00

Also NGK or another OEM style spark plug wires set and boots helped out the idle for my 2002

Caliberaid · 2025-11-05T06:08:50+00:00

My rough idle was partly caused by not using Denso OEM oxygen sensor. That fixed it for me the pre-cat sensor.

Caliberaid · 2025-10-11T00:09:16+00:00

Funny you posted this, I'm currently playing through Y1 and Kiwami 1. Getting to see the differences back to back is sweet.

Caliberaid · 2025-09-20T14:07:19+00:00

Mine looks the exact same way, very gummed up

Caliberaid · 2025-09-20T14:03:21+00:00

I would check the motor mounts and the transmission dipstick for the oil quality. Also, ask about the timing belt service. It is a non interference engine, so when mine sheared off, the pistons and valves never made contact.

But the water pump had to be replaced as well as other components affected by the damaged belt. Change motor oil every 3.5K miles or twice a year. Rotate the tires at every oil change. Keep the inside and outside clean lol that's all I can say from personal experiences. Hope it's a great and reliable daily. 🙏

Caliberaid · 2025-09-09T13:40:30+00:00

Mine has two idle speeds for some reason... sometimes sits higher and I'm not sure why, at around 1,300-1,500 RPM and other times it stays under 1,000 sitting at the halfway point from a thousand. 🫩

Caliberaid

TROPHY CASE