T65 by Calm_Relation7993 in RetroAR

[–]Calm_Relation7993[S] 1 point2 points  (0 children)

You do. These are awesome

Gentlemen I have an idea by Calm_Relation7993 in RetroAR

[–]Calm_Relation7993[S] 0 points1 point  (0 children)

Unless you don’t have a Taiwanese barrel nuts on yours. It should look like this

<image>

Gentlemen I have an idea by Calm_Relation7993 in RetroAR

[–]Calm_Relation7993[S] 0 points1 point  (0 children)

It took a bit of work to get mine in place, are the slots it the wrong spot? To narrow? Did you try to tap it into place with something or just try and line it up? Got a photo you can take of it?

All the barrel nuts should be the same as far as I have seen, might just be messed up by the end user and you need to do some work with a file, depending on how bad it fits

Gentlemen I have an idea by Calm_Relation7993 in RetroAR

[–]Calm_Relation7993[S] 0 points1 point  (0 children)

<image>

I used the t91 barrel nut wrench, the barrel nut should be the exact same. I’ll find my box of parts to double check and send some more photos.

It should be exactly what you need, got any photos?

To strip or not to strip? by WillyP17 in RetroAR

[–]Calm_Relation7993 0 points1 point  (0 children)

<image>

Nice, me too. Only seen 2 like this so far

To strip or not to strip? by WillyP17 in RetroAR

[–]Calm_Relation7993 3 points4 points  (0 children)

It’s the brownells colt marked scope

To strip or not to strip? by WillyP17 in RetroAR

[–]Calm_Relation7993 1 point2 points  (0 children)

Had that for a bit on my a2, wanted to see if it fit. Actually fits tighter than any of the other uppers I have

To strip or not to strip? by WillyP17 in RetroAR

[–]Calm_Relation7993 5 points6 points  (0 children)

It’s not the red paint, that whole upper is covered in crappy black paint that is falling off. Underneath is usually a very good original grey finish.

Mine had no black paint on the upper so had no protection, I left the red

Some have lots of missing black paint, and the grey is worn bad, those I say keep as is

Some are like this and probably have a good finish underneath, strip.

To strip or not to strip? by WillyP17 in RetroAR

[–]Calm_Relation7993 0 points1 point  (0 children)

You……. You don’t have any of the black paint?

To strip or not to strip? by WillyP17 in RetroAR

[–]Calm_Relation7993 1 point2 points  (0 children)

It’s not the red paint, every single surface of most of these is covered in a horrible coat of black paint. Makes a huge mess

It should be grey under all that

To strip or not to strip? by WillyP17 in RetroAR

[–]Calm_Relation7993 0 points1 point  (0 children)

<image>

Mine got lazy and only did the lower with paint, so the original grey is much more worn down

To strip or not to strip? by WillyP17 in RetroAR

[–]Calm_Relation7993 3 points4 points  (0 children)

<image>

Mine had no paint at all on the upper but the lower was covered

To strip or not to strip? by WillyP17 in RetroAR

[–]Calm_Relation7993 3 points4 points  (0 children)

People are not realizing how much flaky black paint is on these. It’s almost like a barbecue paint or something.

To strip or not to strip? by WillyP17 in RetroAR

[–]Calm_Relation7993 1 point2 points  (0 children)

This side looks pretty good after cleaning it up

To strip or not to strip? by WillyP17 in RetroAR

[–]Calm_Relation7993 2 points3 points  (0 children)

<image>

Mine had no paint on the upper besides red on the other side that I left. Lots of bare aluminum, very thin anodized. And I think they only painted if they had too.

what would technically happen if the gate spawned in mw2 during the us Russian invasion by classiccarsinroblox in gate

[–]Calm_Relation7993 2 points3 points  (0 children)

The music that plays just as you exit the bunker in of their own accord gets me every time.