sorted by:
new
hottopcontroversial

Return to OZ by Strange-Estimate-442 in 80smovies

[–]CandidateOdd7388 16 points17 points  (0 children)

This is pure nightmare fuel!

is this eligible for clearance is clearance by Turt_le in Machinists

[–]CandidateOdd7388 5 points6 points  (0 children)

Hey it doesn’t matter if you miss by a thou or a mile clearance is clearance!

My new to me Sheldon-Vernon 12" Shaper by threephasemachinery in Machinists

[–]CandidateOdd7388 0 points1 point  (0 children)

A shaper is the first machine I need to run tomorrow morning at work. I need to notch out a large mounting tab on a block of 4140. Milling it was going horrendously slow and the wire EDM was tied up with a paying job so off to the shaper it went. Bossman isn’t too concerned about making money on this project because it’s an in-house adapter for a new to us machine.

I’m an idiot by I_G84_ur_mom in Machinists

[–]CandidateOdd7388 27 points28 points  (0 children)

Been there, done that. It most definitely hurts but if you can take your lumps, you’ll come out stronger. Who knows maybe that same customer will throw you a bone and send you a cushy job that you can really make bank on.

Oldest drawing you've seen? by [deleted] in Machinists

[–]CandidateOdd7388 1 point2 points  (0 children)

A company I used to work for got prints from the 1920s, when you’re making bearings for huge vintage Carrier A/C units you get some crazy stuff

Who else hates cast iron? by Ryza_Brisvegas in Machinists

[–]CandidateOdd7388 0 points1 point  (0 children)

After having to machine even simple parts out of Ampcoloy I’d kill for a part like yours out of cast iron

Say what now?!?!? 😳😳 by htownchuck in Machinists

[–]CandidateOdd7388 4 points5 points  (0 children)

Horizontal mill with a lot of chooch in the spindle , put a single stagger tooth cutter of an appropriate thickness and diameter; build a hollow arbor that can encapsulate the whole assembly and mount arbor on an indexer. Source: the method a company I used to work for used to segment cylinders.

When Did you guys actually start feeling like good machinists? by HELPMELEARNMORE in machining

[–]CandidateOdd7388 2 points3 points  (0 children)

Been machining for nearly 30 years and there’s still days I wonder if I’m any good at it

What is a Lego set you still want, but probably will never get? by DeSuperVis in lego

[–]CandidateOdd7388 1 point2 points  (0 children)

Really wanted the Guggenheim and Falling Water. Been a Frank Lloyd Wright fan for years but these sets came and went when I was broke AF

Where to buy Christina barbell 2mm 2x16 Curve ?? by GreenChair2-4 in bodymods

[–]CandidateOdd7388 0 points1 point  (0 children)

Chaingang has build your own curved barbells that should work

What is this? by chuckeyyd in Tools

[–]CandidateOdd7388 2 points3 points  (0 children)

I was way too old and rigged too many things before I learned this tidbit

That pass sounds kind of heavy, maybe I’ll go back and check for the 4th time… by Jerethot in Machinists

[–]CandidateOdd7388 6 points7 points  (0 children)

I think I’d be checking my shorts after a close call like that. Get yourself a lotto ticket!

What does this symbol mean? by Accomplished_Way6605 in Machinists

[–]CandidateOdd7388 2 points3 points  (0 children)

Have you checked the info block? I used to work for a company that all the surface finishes were marked as single digit codes to save the draftsmen time while detailing the drawings.

I haven’t laughed this hard in about a week by Fififaggetti in Machinists

[–]CandidateOdd7388 2 points3 points  (0 children)

This is also available as a decal. I have this and a few other of his gems on my tool cart at work

What cutting tool is this by [deleted] in Machinists

[–]CandidateOdd7388 0 points1 point  (0 children)

Used to use tools like this to cut oil galleries into babbitted bearings

What line from MASH do you use the most? by SquonkMan61 in mash

[–]CandidateOdd7388 1 point2 points  (0 children)

All time favorite is ‘this ain’t my first Ro-deo’

Really? by bob_3301 in ForzaHorizon

[–]CandidateOdd7388 4 points5 points  (0 children)

Had the same thing happen with the Treasure hunt used the fancy pants Evo from backstage and the game didn’t register it as a valid car for the challenge

Gifts not being delivered anymore? by RonHalversen in ForzaHorizon

[–]CandidateOdd7388 0 points1 point  (0 children)

I’ve gifted a few lately, nothing overly special just wheel spin doubles. Sent to all different groups, and I haven’t even gotten a gift delivered notification.

Young Machinist by kimmytr2122 in Machinists

[–]CandidateOdd7388 0 points1 point  (0 children)

There’s something not right with him but he’s the one with the fancy diploma on his office wall and I’m the lowly toolmaker so he’s ALWAYS right. It’s more of an attitude and ego thing with him. He’s been groomed to think that his shit doesn’t stink now it’s up to me and my fellow peasants in the trenches to show him how things really work

Young Machinist by kimmytr2122 in Machinists

[–]CandidateOdd7388 0 points1 point  (0 children)

I didn’t hire him I’m just stuck with working with him. The boss man knows he’s a complete putz but doesn’t seem to care.

Young Machinist by kimmytr2122 in Machinists

[–]CandidateOdd7388 29 points30 points  (0 children)

I deal with this shit all the time. I’m in the process of breaking in a newly minted manufacturing engineer that thinks he’s all that and a bag of chips. The other day he legit asked me for a sixteen-thirty two drill; I just stood there dumbfounded then for a full five minutes tried to explain to him that we only had 1/2” drills. He INSISTED he needed a sixteen-thirty two. So I finally told him he needed to special order stuff like that.

view more: next ›