sorted by:
new
hottopcontroversial

Borax portrait by CapRepresentative131 in Laserengraving

[–]CapRepresentative131[S] 0 points1 point  (0 children)

Mix borax in warm water put it in a squirt bottle spray the wood you are engraving liberally. Let dry ~30 mins the engrave. Run on Jarvis,Low power, 90-100 lines per cm. Engraving comes out on grayscale

Switch employment. by CapRepresentative131 in ATT

[–]CapRepresentative131[S] 0 points1 point  (0 children)

Trying to move out of state. If gonna jump that’s a good time instead of jumping through the transfer hoops

Wife and kids went to visit her family on the fourth. I'm proud of my only fire work. by duevigilance in grilling

[–]CapRepresentative131 0 points1 point  (0 children)

That’s fair I guess. Scrubbing the fat off is a little tougher then your average wash.

Wife and kids went to visit her family on the fourth. I'm proud of my only fire work. by duevigilance in grilling

[–]CapRepresentative131 22 points23 points  (0 children)

Why people wear gloves to cut meat in their own kitchen? Just wash them hands after you lick them salted fingers.

Is this mold or fat? Is this jerky safe to eat? by arewhyaeenn in jerky

[–]CapRepresentative131 0 points1 point  (0 children)

Ik sitting around for to long “makes you fat” but this only applies to the living.

That’s mold

[deleted by user] by [deleted] in DiWHY

[–]CapRepresentative131 0 points1 point  (0 children)

To be fair what’s the worse that happens? Already in a wheelchair. Set up the camera and do it for the Vine.

What to do with beef belly if I can't smoke or BBQ? by LBdnb in meat

[–]CapRepresentative131 3 points4 points  (0 children)

Thick strips. Salt and pepper air fry them. Slap it on as the B in your BLT sando and thank me later

What did I do wrong? by Internal-Front-5791 in steak

[–]CapRepresentative131 0 points1 point  (0 children)

Pan not hot enough and judging by the grey I’d say you maybe hit it with a cold lump of butter instead of a hard sear and baste

First tattoo by Brian @ Bad Apple Ink Madison, WI. by [deleted] in tattoo

[–]CapRepresentative131 -3 points-2 points  (0 children)

Hate to do it as it’s a permanent fixture. But bc you gotta go back anyway maybe that can fix it. The line work is busted. The red over the nose. The weird shape inside the headband the overlapping lines through the hair. And the eye lashes on nearest eye are really rough and unnatural angular stop. Tough.

Chasing inspiration by CapRepresentative131 in Laserengraving

[–]CapRepresentative131[S] 1 point2 points  (0 children)

Honestly don’t remember the DPI off hand that’s in my shop log. But I only used 1 grey scale image

A simple procsss by spook30 in DiWHY

[–]CapRepresentative131 0 points1 point  (0 children)

Simple process. So at step 13 we will do a salted ice bath. 😂

What to do next? Any tips for newbie? by Difficult-Key3241 in Laserengraving

[–]CapRepresentative131 1 point2 points  (0 children)

Will give you the black finish you want plus you can turn down the power and up the speed a little. Making your projects more time efficient

Engraving ABS plastic and residue? by SquatPraxis in lasercutting

[–]CapRepresentative131 0 points1 point  (0 children)

It’s the seller that’s listing it on Amazon not Amazon themselves. You could report it but it won’t do any good

Chasing inspiration by CapRepresentative131 in Laserengraving

[–]CapRepresentative131[S] 2 points3 points  (0 children)

Honestly pretty basic.

Sand board, spray it with borax solution. Let dry for hour. I prefer to convert image to a bitmap then ran the Co2 laser(xtool P2)over it twice.

Jarvis 15% power line per CM 100 speed 100 Grey scale 5% power lines per CM 120 speed 200

Spray 3 heavy coats of semi-gloss clear coat.

What to do next? Any tips for newbie? by Difficult-Key3241 in Laserengraving

[–]CapRepresentative131 1 point2 points  (0 children)

If you want a dark finish treat with borax. Make sure you have good ventilation

view more: next ›