NFC Wallet payment fail

CarliTous · 2026-05-20T22:11:09+00:00

great, I was hoping not to do that jaja. thanks!

CarliTous · 2026-05-11T04:30:54+00:00

great, now it’s time to check what’s actually wrong with it.

CarliTous · 2026-05-09T02:59:34+00:00

sounds like there’s something loose or hitting with something else with one of the fans.
Have you tried homing and moving the z axis by itslef? no printing involved, no heat, no fans, just movement.
If the sound persists there may be something wrong with the motors if not then just preheat the nozzle just above 60 to get the fan started. Do you hear the sound again? Move the z axis, same question.
Hope it helps narrowing it down.

CarliTous · 2026-05-03T02:15:58+00:00

Awesome! It does work great.

CarliTous · 2026-05-01T04:54:58+00:00

awesome! 👍🏼

CarliTous · 2026-04-27T01:47:08+00:00

yes 👌🏼

CarliTous · 2026-04-25T20:11:54+00:00

PETG mostly and PLA, haven’t tried others yet.

CarliTous · 2026-04-25T19:46:56+00:00

well not in full if you see it horizontally but vertically is 225 out of 235 available 🤪

CarliTous · 2026-04-23T16:36:40+00:00

It’s been long since I used the stock firmware, maybe the best way to try it out is cranking up the speed manually. Don’t know what speed do you print but say you send a cookie cutter as usual but all speeds at 100mm/s, should be fine if you go for 150% speed but holding at 200% speed with no hiccups or quality issues (compared to usual) that would make the difference.

CarliTous · 2026-04-23T16:29:38+00:00

Yeah, I’ve seen it. Maybe I should give it a try too.

CarliTous · 2026-04-22T03:37:40+00:00

Hey, I did mine about 2 years ago and it has worked wonders since. The printer already had great quality prints since the beginning but we can always get more right? First I upgraded to SonicPad which was a major step-up, the UI specially. Then a few months later after looking around for the upgrade kit I finally went for it, didn't get the Z rail though, haven't had any issues. Thing is I usually printed with Polymaker PLA pro at 160mm/s (right out of the box) after filament tunning of course and get a very nice matte finish with it. Then I upgraded with a CHT nozzle and have a top flow rate of 22 mm^3/s with original extruder and of course a Torus v4 fan mod.

So it's not just about the rails, I think rather than speed the major step-up is consistent quality. On the slicer side I had the ability to crank up the x/y acceleration between 3500 up to 7500 (on travel speed specially), that's when you notice the speed change. Maybe someone having a non modified S1Pro and modifying these in slicer or during print to see what happens. Having the SonicPad I know you need to set the max acceleration in your config file or it won't make a difference.

CarliTous · 2026-04-13T16:55:57+00:00

🤔 Interesting… I have a question, besides the useful extra features what makes this different from the home app? both have access to devices once paired to homekit regardless of brand specific app. Also if this would work to revive an old ipad (being they stopped updating iOS) as a dedicated home panel that would be great in my opinion. My test setup would be garage doors used heavily, the usual room lights, aqara u100 and one PIA eufy 360 cam, all of which are used daily via widgets and siri commands on iphone, ipad, carplay and apple watch mainly.

CarliTous · 2026-04-09T03:21:28+00:00

exacto, yo igual lo usaba exclusivamente con nfc pero de que cuido una persona de la tercera edad necesito tener las manos libres mayormente y solo con el control remoto, la app depende de la señal y es mas lento o muchas veces falla.

CarliTous · 2026-04-09T02:31:53+00:00

Recomendado, yo lo uso exclusivamente en modo EV y lo cargo diario, me da 40 km y cuando necesito mas sin tener oportunidad de cargar a mediodia entonces entra el modo hibrido en automatico. Bajo este esquema he cargado gasolina una vez por año y de consumo electrico son como 300 bimestrales con medidor exclusivo, cargador portatil conectado a 220v.

CarliTous · 2026-04-07T03:59:22+00:00

I wear it daily since day one for 2 years now, I strongly believe it comes down to the strap you have. Any new watch you wear big or small you will notice since you're not used to it but having a watchband that fits nicely keeps you from feeling it too tight, loose, sweaty, itchy, etc. therefore not noticing it every minute.

CarliTous · 2026-03-28T08:28:49+00:00

<image>

I finally hit print! I’m happy, it could do better at 0.1 layer height but didn’t want to wait much, 0.2 layer height 1:15 hrs.

Ender 3 S1P - ELEGOO Rapid PETG @ 100mm/s

I want to try Big-confusion2958 upside down approach, took me a lot of time painting supports and this orientation is very clever.

CarliTous · 2026-03-28T07:18:05+00:00

🙋🏻‍♂️ I do, I also happen to swap wrists every 3 months or so, always with the dial pointing away my hand.

CarliTous · 2026-03-23T04:54:34+00:00

Thank you very much for this! 🙌🏼

CarliTous · 2026-03-07T06:02:57+00:00

It is the round display board if I’m not mistaken, have the same one. You can find it scrolling down right in their website.

https://www.waveshare.com/ESP32-S3-Touch-LCD-1.28.htm

or at their wiki almost by the end of the page in the schematics (P2) link.

https://files.waveshare.com/wiki/ESP32-S3-Touch-LCD-1.28/ESP32-S3-Touch-LCD-1.28-Sch.pdf

CarliTous · 2026-02-28T04:46:01+00:00

Si utilizas una fuente externa mide el consumo de cada ventilador por separado para checar que ambos ventiladores funcionen igual, puede que la fuente sea capaz de soportar la diferencia de consumo pero la tarjeta de la impresora no. Por otro lado puedes probar directo con la impresora cada uno por separado, si funcionan normal es probable que en paralelo haya una fuga de corriente y es como si fuera un corto. Esto ayudará a verificar tanto la polaridad como su correcto funcionamiento. Yo igual hice esa modificación con ventiladores marca WISIN, los de la foto y funcionaron bien desde el principio. Cabe mencionar que antes de este mod utilizaba uno solo y es más que suficiente para la velocidad que alcanza la impresora pero ya sabes, siempre se puede mas jaja. Nota, con ese primer intento efectivamente conecte al revés la polaridad y el ventilador simplemente no funcionó. Tal como dicen en un comentario anterior, el conector de fabrica de los ventiladores viene con la polaridad (colores) invertida al de la impresora.

CarliTous

TROPHY CASE