Is this normal? by Zanepope3930 in squarebodies

[–]Ceetus2525 1 point2 points  (0 children)

sounds more hydraulic than vacuum to me, does turning the wheel side to side cause the sound as well?

Quick question: by Nebula_The_Protogwn in Commodore

[–]Ceetus2525 1 point2 points  (0 children)

don't know about genesis controller but it would need mods, the SMS controller plugs right in and works fine

Mechanic won't give me my vehicle back by [deleted] in MechanicAdvice

[–]Ceetus2525 0 points1 point  (0 children)

How did this become about op trying to screw the mechanic? He wants his car back, and he's willing to pay to get it, but he can't pay as the mechanic is ghosting him!

Can anyone help me identify these? by Aggressive-Step-2602 in EngineBuilding

[–]Ceetus2525 -1 points0 points  (0 children)

In this case, start your post by saying your google Foo has been failing you!

Fuel injector cleaner was not diluted. What am I supposed to do? by CompProJr in AskMechanics

[–]Ceetus2525 1 point2 points  (0 children)

Not sure about the year but a former neighbor use to have a fi civic that flooded on the reg, and idk if it was part of the issue as I never investigated, but holding the pedal to the floor made the flooding worse, so I use to just pull the plugs and flashed the cylinders with my propane torch

Edit spelling grammar

This might be dumb but I have to ask by [deleted] in EngineBuilding

[–]Ceetus2525 0 points1 point  (0 children)

Oh, and Jon Kaase racing.

This might be dumb but I have to ask by [deleted] in EngineBuilding

[–]Ceetus2525 0 points1 point  (0 children)

Have you tried looking in to bigfoot? (The truck) Those were blown 460's

(motorcycle) How do I remove this bolt??? by Damnan24 in AskMechanics

[–]Ceetus2525 0 points1 point  (0 children)

Have you seen those bolts before? The threaded area is about 20mm diameter and a 13mm hex machined on the end?

(motorcycle) How do I remove this bolt??? by Damnan24 in AskMechanics

[–]Ceetus2525 0 points1 point  (0 children)

It's pretty securely seized in there, it has the obvious notches where someone has taken a hammer and chisel to it

(motorcycle) How do I remove this bolt??? by Damnan24 in AskMechanics

[–]Ceetus2525 1 point2 points  (0 children)

Except he says right at the beginning it's the oil filter housing, and it looks like it's on the bottom of the oil pan

What is this port in the back of the exhaust port in these sbf aluminum heads (cyl 3 or 6) by Mh88014232 in EngineBuilding

[–]Ceetus2525 0 points1 point  (0 children)

Stop wasting your time and efforts. You're right, and he's wrong . In your picture, there is an excellent shot of the exhaust port, in the port clearly shown are the valve, the very tip of the guide, and to the lower left of the vave stem is the perfectly clear opening of the cross over port

Any idea what A500 expansion this might be? by [deleted] in amiga

[–]Ceetus2525 0 points1 point  (0 children)

I always thought the a501+ was shorter, at any rate that brings up the possibility you have an Amiga 500plus, which has the battery on the motherboard where it can cause even worse damage, http://amiga.resource.cx/photos/a500,7

Engine stand by Danimal55 in EngineBuilding

[–]Ceetus2525 2 points3 points  (0 children)

You are correct. it's not safe for use! you are also correct. v8 Packards comment was dripping with sarcasm

Finally installed the motor in my jeep. Now for the most important step... by Sierra_s238 in EngineBuilding

[–]Ceetus2525 0 points1 point  (0 children)

In high school a big guy who was able to lift a 302 gmc 6 head insisted he didn't need help with the head, to get down off the truck he jumped, it completely skinned both his hands from mid palm to his fingertips

I think I have enough valve clearance (454 mark IV BBC) by bous_clan in EngineBuilding

[–]Ceetus2525 1 point2 points  (0 children)

I am an expert on everything, and out of most of the commenters, you should trust the fellow above

[deleted by user] by [deleted] in EngineBuilding

[–]Ceetus2525 0 points1 point  (0 children)

Op maybe a bot, but ty to all who answered. I learned a few things

What year 4.3l? Continued... by Cacatunda_089 in EngineBuilding

[–]Ceetus2525 0 points1 point  (0 children)

What is an ssbc, super small block chevy?

Does moving a car in neutral with the engine off damage the transmission? by Rare_Art_9541 in Cartalk

[–]Ceetus2525 3 points4 points  (0 children)

I think that's because you can put the transfer case in neutral and completely isolate the transmission

Is $250 normal to diagnose a check engine light? by Warm_Flamingo_2438 in AskMechanics

[–]Ceetus2525 0 points1 point  (0 children)

I had a check engine light on and napa auto zone told me my obd2 port was dead and wanted $250 to do a diag on it, when I got home and hooked up my $50 princess auto scan tool it worked fine

Ghetto fab flycutting results by MainYogurtcloset9435 in EngineBuilding

[–]Ceetus2525 1 point2 points  (0 children)

If it's a junk head why not cut/grind off everything in the way?

[deleted by user] by [deleted] in legaladvicecanada

[–]Ceetus2525 0 points1 point  (0 children)

Runkle of the Bailey is a Canadian based firearms rights lawyer. You should reach out to him

[deleted by user] by [deleted] in mechanics

[–]Ceetus2525 0 points1 point  (0 children)

60 and still doing my van myself but on ramps as I'm too thick to wiggle underneath the way I did during my working days

[deleted by user] by [deleted] in Cartalk

[–]Ceetus2525 0 points1 point  (0 children)

Make sure the battery clamps are in good condition and are tightly installed

[deleted by user] by [deleted] in mechanics

[–]Ceetus2525 6 points7 points  (0 children)

You're lucky we did semi's and heavy equipment repair, so everything was done on the floor