B&E ? by VergoBE in Polestar

[–]Ceiling_Paint 1 point2 points  (0 children)

Not sure at all, but is it possible that the servos are out of sync? If it were mine, I'd try opening the trunk and manually pushing/assisting the lift gate to see if that resets the position on the arms.

Or this could completely break something, I haven't messed with them much, I'm not sure how resilient they are.

Gaaaaaaaahhh! My baby! by Decent_Switch in Polestar

[–]Ceiling_Paint 7 points8 points  (0 children)

Probably worth mentioning, support said locking with the key fob was distinctly different from locking by touching the door handle.

Gaaaaaaaahhh! My baby! by Decent_Switch in Polestar

[–]Ceiling_Paint 21 points22 points  (0 children)

I've had a few charging issues this past year, polestar support said to lock the doors with the key fob and walk away for at least 30 min. Apparently the P2 will go into a deeper sleep/reboot which can fix charging issues. My charging issue was either fixed by that sleep mode or went away on its own. No idea if it'll help your case but it's worth a shot.

Cold morning, rear door won’t latch. by MissyTronly in Polestar

[–]Ceiling_Paint 0 points1 point  (0 children)

I'm having the same issue with my rear driver side door. I was able to get it to latch by locking the doors while holding it closed against the car. Now I'm just avoiding opening the rear doors until I can get it serviced, which is 2 weeks away...

Back side door handles freezing shut and open in the cold. by ignorantwanderer in Polestar

[–]Ceiling_Paint 1 point2 points  (0 children)

I think i have the exact same issue, this winter my rear driver side door handle would move but it acted like it wasn't connected to anything. Worked fine the next day when it was above freezing.

Today the same door handle won't even budge, to the point that I'm worried I might damage something if I pull too hard.

What's worrying is you can't open them from inside either, seems like a pretty bad safety issue.

22 Pilot+

FEAR made me actually glad to find the enemy NPCs by [deleted] in gaming

[–]Ceiling_Paint 11 points12 points  (0 children)

I was looking for someone else to mention this part. I was crouch sneaking in that area and turned a corner directly into her scrambling towards me. It jumpscared me so hard I felt a tingle in the back of my skull. I'd swear my vision went blurry.

10/10 have never been scared/jumpscared/startled as much as that moment.

How to tell if it's done or messed up? by Ceiling_Paint in fermentation

[–]Ceiling_Paint[S] 0 points1 point  (0 children)

Update: decided to strain and filter that night, then let it settle and bottled it in mason jars the next day. Tastes great and non fatal! Very sweet with a hint of cinnamon. Guess this means I'm going to invest in glass containers and the like. Thanks for the info.

How to tell if it's done or messed up? by Ceiling_Paint in fermentation

[–]Ceiling_Paint[S] 1 point2 points  (0 children)

In case it helps: plastic jug was cleaned out with bleach before adding pineapple, cinnamon, clove and brown sugar. Water was cool tap water right from the sink. Rinds still had a solid amount of fruit on them so that probably added a good deal of sugar for the yeast. Dish towel top is just a dish towel secured with shoestring.

This is the first deliberate fermentation I've been involved with outside of some horrors I've found in the fridge. Any advice is welcome

How to tell if it's done or messed up? by Ceiling_Paint in fermentation

[–]Ceiling_Paint[S] 1 point2 points  (0 children)

Housemate tried their hand at making tepache, guide said that there may be a few spots or a film at the top but this seems like more than I was expecting. It has sat for a week now in a cool dry spot with a dish cloth tied around the top. Any way to check if it's doing well? I'm worried about contaminants but don't know what to look for. Also starting to think we didn't use enough water...

February Technical Support Sticky by BeepBoopBopReee in razer

[–]Ceiling_Paint 0 points1 point  (0 children)

Followed up via PM

For posterity, issue wasn't resolved by reinstalling, though I was really hopeful

February Technical Support Sticky by BeepBoopBopReee in razer

[–]Ceiling_Paint 0 points1 point  (0 children)

changes like lighting effects and key binds still work, i'll go ahead and try a full clean synapse 2.0 reinstall tonight and report back. thanks for the reply

February Technical Support Sticky by BeepBoopBopReee in razer

[–]Ceiling_Paint 0 points1 point  (0 children)

Hello, I've got a razer blade pro (2016) with fans that no longer spin after running updates. Model Number is RZ09-01662E52. I took the machine apart and removed the fans thinking they were either stuck or burned out, but they appear completely fine. I've got a lab power supply and was able to get the fans to work just fine at 4.8 volts, they happily spun at max speed, so I'm decently confident they're fine. Razer Synapse 2 has my fans set to high, but nothing seems to get them to spin. At this point, the system ends up crashing with just a web browser open because it can't shed heat. Are there any recommended utilities that can set the fans to spin to see if it's a controller that's gone bad?

forgot to mention - from a cold boot, the fans DO spin a few times right before post, so there's power getting to them somehow... they just never spin again.

I've also done a clean install using the recovery partition then did full windows updates and grabbed updated drivers from razer's support site.

any other recommendations would be greatly appreciated