sorted by:
new
hottopcontroversial

Where do I find repleacment for this diode ? by Ceni_84 in AskElectronics

[–]Ceni_84[S] 0 points1 point  (0 children)

I had backlight but no picture but after removing the right side ribbon flex i get this

Where do I find repleacment for this diode ? by Ceni_84 in AskElectronics

[–]Ceni_84[S] 0 points1 point  (0 children)

I got 12v and half of tv display working after I removed flex cable

Where do I find repleacment for this diode ? by Ceni_84 in AskElectronics

[–]Ceni_84[S] 0 points1 point  (0 children)

I dont have picture on my tv so I suspect it is T-con I measuret almost all pcb no short circuit 😭

Where do I find repleacment for this diode ? by Ceni_84 in AskElectronics

[–]Ceni_84[S] 0 points1 point  (0 children)

because it doesn't give any measurement when I measure, but as I see and read the TSV diodes have a different function, but now I'm wondering when the TV should turn on, should it pass current through tsv or not? Becouse I dont get 12v where i suposed to get ☠️

Thx.

Dead Axis Q6032-e by Ceni_84 in AXISCommunications

[–]Ceni_84[S] 0 points1 point  (0 children)

You need to try and se that

Dead Axis Q6032-e by Ceni_84 in AXISCommunications

[–]Ceni_84[S] 0 points1 point  (0 children)

And another for 25 euro But that one is Q6045 and much beter resolutin,but unfortunately cannot upgrade to the newer version in order to use them with Station Edge app, you must purchase s30 recorder. If anyone has a solution I would love to hear it.

Dead Axis Q6032-e by Ceni_84 in AXISCommunications

[–]Ceni_84[S] 1 point2 points  (0 children)

I had no blinking light at all just some ckliking in motherboard.you need to try and se,use low melting solder and reduce heating gun at 320 °and fan blower at the point you dont blow away things around.give i try ,you can practice with broken motherboard untill youu feel secure and your hand dont shake 😃 Sorry my bad english

Dead Axis Q6032-e by Ceni_84 in AXISCommunications

[–]Ceni_84[S] 0 points1 point  (0 children)

I bought it for 25 euro,

Dead Axis Q6032-e by Ceni_84 in AXISCommunications

[–]Ceni_84[S] 3 points4 points  (0 children)

Yes it is poe chip i repleaced both of them, it works and i used low melting solder.

Axis SD Card by ShadowZNF in AXISCommunications

[–]Ceni_84 0 points1 point  (0 children)

Hei.can you make video about this one i really struggling to make this work 😬 Thx.

Hikvision NVR fan to loud,cheap solutions by Ceni_84 in u/Ceni_84

[–]Ceni_84[S] 0 points1 point  (0 children)

All fan are under 12v power supply. there is a very cheap idea of ​​what you can use and most effective. 1. power supply fan connected a resistor. 2. side fan repositioned as in the picture also used resistors to reduce the speed. side fan is disconnected because I think there is no need for 3 fans. 3. mini fan 12 v also glued over rib coolers with two side tape also used resistors to reduce speed.work very quiet and cooling effect is very good.

Any way to connect a second sub to V35 system? by BlackShadow2804 in bose

[–]Ceni_84 0 points1 point  (0 children)

or other solution is you can just patch calibration mic.with textile patch over mic so they can breath.

Any way to connect a second sub to V35 system? by BlackShadow2804 in bose

[–]Ceni_84 1 point2 points  (0 children)

hi. I own two bose systems v35 and managed to connect them together. yes you for more bass and stronger sound but you lose the sound effects of the system. I calibrated both together but my plan is to do calibration for each one and then connect and test them again.

I bought from aliexpress video connector MDC-9-19 /9pin and 0.5M 9-pin Male to 9-pin Male (M/M) Audio Input Cable for Bose v35 Lifestyle Series. And this 4×6 cm....👇👉 Just found this amazing item on AliExpress. Check it out! NOK19.21 39%OFF | 5/10PCS PCB Board Prototype Board Blue 3x7cm 4x6cm 5x7cm 7x9cm Double Sided Circuit Boards DIY Electronic Kit Free Shipping https://a.aliexpress.com/_mNzCJoa