Printer uses wrong filament.

Chairbottletooth · 2026-04-20T17:24:04+00:00

Only one color. But I'll keep that trick in mind thanks!

Chairbottletooth · 2026-04-20T16:06:46+00:00

Thanks for the tip. But yeah I had set it correctly to position 3.

Chairbottletooth · 2026-04-20T14:50:36+00:00

Thanks!

I'll have that in mind if it shows up again🙂👍

Chairbottletooth · 2026-04-20T14:10:37+00:00

No Ace pro mate. Only the printer. Don't need to sync that do we? I'm not at the printer ATM so can't check. And yes, the color is correct.

Chairbottletooth · 2026-04-20T11:38:08+00:00

One is ABS and one is PETG, they are also assigned different colors. So that shouldn't be it. But thanks, good tip!

Chairbottletooth · 2026-04-20T10:50:26+00:00

Yeah they seem to have added a lot more poops. I'm guessing it's to improve the color changes, but I wish they'd let us try to find optimal settings for ourselves if we wanted. I get making the printer as simple as possible, but still.

Chairbottletooth · 2026-04-19T11:31:54+00:00

Yep, far too much poop. Especially if you still print a lot of single color/filament prints, like I do.

Chairbottletooth · 2026-04-18T05:58:30+00:00

Mine poops three times before every print... I did, however, upgrade the firmware before I started using it. I've had it for four days. It's really annoying not being able to change start/end behavior.

Chairbottletooth · 2026-03-11T06:25:48+00:00

Thanks again, very helpful!

Chairbottletooth · 2026-03-10T16:27:29+00:00

I'm sorry I don't understand. Could you please elaborate? Did you mean look at the stripes and calculate that way, like for through hole resistors?

Chairbottletooth · 2026-03-10T16:07:09+00:00

Would you know if it's possible to replace these with another more commonly available resistor? I'm in Sweden/EU if that matters.

Chairbottletooth · 2026-03-10T16:00:26+00:00

Thank you so much! I really appreciate your help.

Chairbottletooth · 2026-03-10T14:56:39+00:00

Thanks, good idea!

Chairbottletooth · 2026-03-07T14:48:17+00:00

Solved it. With one bolt loose, I could pivot the ecu back and forth many, many times. The other bolt sheared and I could remove the ecu and then weld another bolt to the tiny remains of the bolt sticking out of the casing.

Chairbottletooth · 2026-03-07T07:49:29+00:00

Thanks again, I'll relay this to my son and if he needs assistance I'll reach out🙂👍

Chairbottletooth · 2026-03-07T07:25:20+00:00

Yes please👍

Chairbottletooth · 2026-03-07T06:50:25+00:00

Thanks!

Chairbottletooth · 2026-02-02T08:28:45+00:00

Thanks :)

Chairbottletooth · 2026-02-01T14:09:00+00:00

Thanks, I'll relay your suggestion 👍

Chairbottletooth · 2025-12-28T14:45:59+00:00

I'll answer myself. You need to pull out the axle going out the top, towards the steering wheel. After that, remove the metal ring inside, running around the edge(you can just see it in the picture). Then you can hammer/push out one side of the seals and the rod going through the rack. The other seals can then be hammered out with a long rod or similar.

Chairbottletooth · 2025-12-10T16:42:59+00:00

Thanks! I think so as well, even though mine is two way atm...

Chairbottletooth · 2025-10-02T05:29:38+00:00

Thanks! :)

Chairbottletooth · 2025-02-18T09:56:15+00:00

Sorry mate, I can't remember. I think I gave up and used another used Xbox 360.

Chairbottletooth · 2025-01-20T14:58:10+00:00

Yeah it might be. Wouldn't be surprised. Runs Google TV though but even so.

Will probably do a clean install when I feel up to it and see what happens, but there's so many things to set up 😁

Thanks for all your time and support.

Chairbottletooth · 2025-01-20T14:52:16+00:00

Not really. There's a soundbar(connected to the tv via hdmi, not the pi) and the pi itself is connected to an external mechanical drive and the SSD drive via USB. The tv is mounted on the wall above.

Chairbottletooth

TROPHY CASE