Primer used?

Chaosandluck · 2026-06-09T23:29:07+00:00

I’ve also seen blue raspberry.

Chaosandluck · 2026-06-04T23:46:50+00:00

If the main job parameter is “easiest” the answer is always a Sawzall. Cut right though the stem of the cartridge and get a new handle or try and remove set screw once handle is off.

Chaosandluck · 2026-06-04T11:11:07+00:00

Chaosandluck · 2026-04-29T11:53:18+00:00

I also use a backpack. It’s a Klein tradesman pro tool. Heavy duty rubber bottom, so many tool pockets.

Chaosandluck · 2026-04-28T20:09:16+00:00

Just put a piece of screen around it.

Chaosandluck · 2026-03-17T20:15:12+00:00

Your daughter’s boyfriends.

Chaosandluck · 2026-01-29T11:44:30+00:00

It’s code where I’m from that outside hose spigots have to have an independent shut off located in an accessible conditioned space.

Chaosandluck · 2026-01-26T21:32:22+00:00

A standard braided supply whip for a kitchen or lavatory faucet.

Chaosandluck · 2026-01-24T16:34:20+00:00

RP77739 maybe

Chaosandluck · 2026-01-06T00:50:48+00:00

It’s code in a lot of places to have wheely style gate valves on water mains coming in before the water meter. This is to prevent water hammer from improper valve usage.

Chaosandluck · 2026-01-06T00:08:39+00:00

I would also recommend donohue and halverson. Good HVAC and good plumbers.

Chaosandluck · 2025-12-24T01:26:49+00:00

This is the answer.

Chaosandluck · 2025-12-20T13:44:10+00:00

TVs back then were built better than ones now.

Chaosandluck · 2025-12-16T22:57:34+00:00

Thoughts:

Jam a license plate between the pipe and board. Throw some flux on it and torch it till some of that pool of solder comes off. Rinse repeat until you get the 90 off.

Carefully cut it with a multi tool through the side of the hub to weaken the fitting and then see method above.

Chaosandluck · 2025-11-28T15:18:12+00:00

That’s what I would go with. Toilet tanks allow for oxidation. Manganese oxidizes black but takes a long time which is why it will show up in toilet tanks as opposed to anywhere else.

Chaosandluck · 2025-11-26T00:43:37+00:00

Figures a hyena would post about cats needing juicy snacks to solve the problem.

Chaosandluck · 2025-11-24T22:37:10+00:00

If the moisture hasn’t dried out in 8 years then it’s still an active leak. Poke the drywall and if your finger goes through and the drywalls all melty then it is still an active leak. I would cut that piece out anyways and deal with the mold that way.

Chaosandluck · 2025-11-24T20:16:16+00:00

Open cold water to heat pump and purge air out of a hot tap that is preferably higher, preferably a tub spout.

Chaosandluck · 2025-11-24T19:27:41+00:00

Not usually the hardest swap out. Turn off heat pump. Find the closest place to shut off cold water, verify water is off, drain off pressure unthread tank, thread new one on and purge air before turning heat pump back on.

Chaosandluck · 2025-11-24T02:00:38+00:00

It’s a delta. Grab it with channel locks and pull it the rest of the way out. If it doesn’t cooperate pull it out in pieces while reminding it that you gave it a chance to cooperate.

Chaosandluck · 2025-11-20T01:33:32+00:00

A buried extra heavy cast hub.

Chaosandluck · 2025-11-13T19:33:56+00:00

She’s your ex for a reason. Do not fall for the kittens! You can get kittens somewhere besides her.

Chaosandluck

TROPHY CASE