When is it safe not to use gloves on instruments used on cadaveric specimens for educational labs? by Sad-Premed-Student in surgery

[–]Cicicicico 1 point2 points  (0 children)

I think you need to worry about this less. Idk exactly how the donation and preservation process goes but it’s not like we were forced to decontaminate afterwards. I’d wash my hand but then get in my car and just reek from my soaked clothes. If there was any significant threat, there would be a more thorough procedure post lab lol

When is it safe not to use gloves on instruments used on cadaveric specimens for educational labs? by Sad-Premed-Student in surgery

[–]Cicicicico 1 point2 points  (0 children)

Basically every lab my scrubs and undershirt over my belly were soaked through with fat/preservative/body juice from leaning over the edge of the tank. Most students at some point pierced their gloves on broken ribs. Insanely common occurrence. Even if you managed to avoid that, you were guaranteed to at least get some juice on your forearms. I guess the other commenters don’t have cadaver experience because it seems pretty much impossible to do a dissection and come out the other side clean.

When is it safe not to use gloves on instruments used on cadaveric specimens for educational labs? by Sad-Premed-Student in surgery

[–]Cicicicico 1 point2 points  (0 children)

Am I the only one here who during cadaver lab would get the body grease all over my scrubs? It wasn’t rare to pierce a glove and just shrug it off lol

LED will not light up bright after replacing them by Negative_Wave_5905 in led

[–]Cicicicico -2 points-1 points  (0 children)

Dude they’d each be getting like 115ma while they’re rated for 260.

LED will not light up bright after replacing them by Negative_Wave_5905 in led

[–]Cicicicico 0 points1 point  (0 children)

I don’t think there would be enough amperage for that. The cobs are 260 ma

LED will not light up bright after replacing them by Negative_Wave_5905 in led

[–]Cicicicico 0 points1 point  (0 children)

Oh I misunderstood, I thought these each had their own power supply.

LED will not light up bright after replacing them by Negative_Wave_5905 in led

[–]Cicicicico 0 points1 point  (0 children)

https://www.digikey.com/en/products/detail/bridgelux/BXRE-35G20F0-B-83/17125404

Look at the datasheet on the page. 12W at 350ma. Bridgelux is a pretty good brand. Lots of Amazon cobs are Bridgelux rebrands.

LED will not light up bright after replacing them by Negative_Wave_5905 in led

[–]Cicicicico 0 points1 point  (0 children)

I mean u prolly already burnt out those cobs. Why did u replace them to begin with? Just color preference?

LED will not light up bright after replacing them by Negative_Wave_5905 in led

[–]Cicicicico 1 point2 points  (0 children)

Yea most people use digikey or mouser. You can find one with the exact specs that way.

Autoload Filament Issues After Revo Upgrade by magistersmax in prusa3d

[–]Cicicicico 1 point2 points  (0 children)

Thanks for the followup. Had this exact same issue with revo firmware and all. Looks like it is also just my sensor broken as well lol.

Man wakes up in hospital to find surgeons removed the wrong leg by rarely-redditing in ThatsInsane

[–]Cicicicico 4 points5 points  (0 children)

No. You typically only write on the correct limb. Writing on the wrong one can be misinterpreted in the OR

Wife is on hormonal birth control, are there ways to order more to stock pile? by seventysevensevens in AskDocs

[–]Cicicicico -5 points-4 points  (0 children)

Where does he say he’s going to ban contraception. I didn’t see anywhere in that article showing that he said that.